Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Good evening,
How does the nRF52840's own BLE transceiver capabilities compare to the BLE capabilities of the NINA-B306, as follows...
Does the nRF52840 chip have its...
I'm trying to connect external nrf52832 module to nrf52-dk (PCA10040). I use wiring scheme from this picture:
And it works fine for programming. But I can't get RTT...
Hi all,
this is my first project with nordic and ble, hence, I feel a little bit lost and overwhelmed with all the new function and callbacks used in the ble samples....
Hi, I'm a beginner at this so I would appreciate any help thank you!
I'm trying out light_lightness example v4.2.0.
From RTT Viewer, I want the LED to be able to toggle...
I have two dev kit with nrf52833 one as a tag and other as anchor, the kits are made by Ublox and they demonstrate fine the direction finding functionality.
The problem...
I am using nrf52840 mesh v17.0.2 light_lightness server example.
In the original Light lightness server code, you can control LED1 using J-Link RTT Viewer. By sending...
I need my own input handler procedure that cannot wait.
Interrupt handler is directly attached as GPIOTE_IRQHandler (i don't use your libraries) and takes no more than two...
I am new to Nordic. I installed nRF Desptop Connector. I have opened succesfully the sample nRF projects. Now, I want create my own new nRF Connect Project. I tried two ways...
Hi,
I'm trying to set up a custom driver for the VL53L1X Sensor. (nRF9160 + Icarus Board + NCS 1.7.1)
I placed a new folder in drivers/sensor + modify CmakeLists.fr &...
Hi,
Our project team has decided not to using an external MCU to interface with the 9160 over the UART. So we'll need to write our application on nrf9160. The application...
P19 (Debug OUT Connector) on the nRF52840 BLE RF Development Board, PCA10056 (Dev Board) provides the ability to program a nRF52840 BLE board (BLE Board).
Questions:
...
Hi there,
Attempting to use the sample program for direction finding and have been following Case ID: 280319. Have attempted to add the code suggested by Simonr in adding...
Hi,
I'm working on a project using Zephyr and ncs 1.7.1. One of its functions is to stream WAV files from a SD card. It only ever reads data.
The issue I'm having is...
Hi all,
I am using SES in Win10. After I updated my NCS to 1.7.1, I failed to open my solution. However, it runs succussfully in SDK 1.6.1. The infomation is below:
...
Hello.
I am currently working on implementing a PWM control function using nrf52840. I used the function "es_battery_voltage_get()" to read the battery voltage before and...
