I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
We have a custom PCB with GPS circuit copied from the NR9160-dk board.
The default GPS example is working fine. However, we want to combine GPS tracking and LTE-M connection...
Hello,
I am using NCS 1.5.0 and modem firmware 1.2.3.
I have nRF9160 DK version 1.0.0.
I am trying to run "full_modem_update" example firmware on this.
But getting...
HI
I use NRF9160 serial_lte_modem to test NBIOT/MQTT, current SDK is V1.6.0 ,and config mqtt keepalive =1200S.
after 9160 connect net, control mqtt connect my mqtt server...
I have connected 3 Peripheral using Name Filters and 1 central.
I am able to connect and communicate with all correctly.
But I need to identify that conn_handle 0x0 ,...
Hello!
When collecting dc1.4v with SAADC, there is an error of 100uv. SAADC is configured in differential mode, with N-terminal connected to GND and p-terminal connected...
Hi,
I've read in these forums and seen the machine instructions within the C code that nrf_delay_us (which BTW is used to do nrf_delay_ms) is implemented by executing a...
Hi team,
I would like to know the default channel used for data transmission and the frequency of the channel.
Also whether the frequency is configured in the softdevice...
What is the purpose of the external capacitors on DECA and DECN? DECA calls for 1uF and DECN calls for 0.1uF. The datasheet calls these out as "Regulator Supply Decoupling...
Hello,
sorry to border you again, but I have a problem that block me for many days. I read all nordic questions on TWI (I2C) but did not found a solution... :(
I have...
Hi,
We are designing a custom Board using nRF52840 SOC.
We are operating it in Normal mode, using an internal DCDC converter
We have used configuration 5 from the...
Hi there,
I need to transmit 33995520 bytes from nrf52 peripheral device to a Windows/Android device. Currently it takes about 13 to 14 minutes to complete the data transfer...
the flash of the nrf52832-QFAB is 256KB. the softdevice S132 is used which consumes 152KB and the compiled file of the BLE_UART only consumes 98KB (after making the changes...
Hi,
We have a product already on the market for about 2 years, based on nrf52840 and nrf52832.
The product receives data from an 'external device' via UARTE, forwards...
