Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi There,
I am using NRF52840 chips in my system. Right now I am designing antenna for the chips. I think the reference SCH of nrf52840 have been completed the match from...
I'm using nRF52 starter kit (nRF52832AA)
I'm trying to build the ANT+ BPWR tx example from Nordic (17.0.2 + 7.0.1)
Having some issues running it, but removing ant part...
Hi,
I am using nrf17.02 sdk and nrf mesh 5.0 sdk for nrf52832 dev kit.
1) I want to send the data to UART not on RTT while using the mesh example "provisioner" example...
Anyone able to run the nRF9160 DK on Window 7? I see the 3 serial ports and the mass storage device but even though I see the device in the Programmer app I get "Unsupported...
Hi dear,
Good Day!!
I am using nRF5SDK1702d674dde\examples\ble_peripheral\ble_app_uart- software to test the UART over the BLE to my mobile , The BLE was automatically...
Hello,
i am using "ble_app_uart" example code in nrf SDK to connect to bluetooth and to read-write the data after connection through nrf connect application.
write...
We are using a custom board with softdevice S132, sdk14, and freertos and ana nrf52832.
Our ble_app does:
init gpio put up a splash screen via a display on spi
...
I am starting a new project using SDK 17.0.2, DK52 dev board and Segger embedded Studio.
To create the new project I started from ble_app_buttonless_dfu and commented out...
I got the update notice for 3.6.1, the install gets to around 33% then just sits there. This happens both with upgrade and with clean install for me, I left it to hang for...
Hi all,
in my current platform I have:
a DK (we are working to implement HW modifications to use a nrf52 dongle for this purpose) that is performing as a Thread DFU...
Hello,
I am currently trying out the assert mechanism of Zephyr.
I have added CONFIG_ASSERT=y to my prj.conf file and included " sys/__assert.h " in my main.c .
My program...
Hi,
May I ask what's the minimum reference circuitry for running nrf52840 without RF? Thanks.
My scenario is as follows.
1) RF, eg, Antenna is not needed
2) GPIOTE...
Hi,
I'm developing a CENTRAL using 52832 to connect a earphone.
1.When I enable LESC, the pair fails with the AUTH_NOT_SUPP error. Why ?
What I think if the earphone...
Hi.
I'm trying to use direct advertising to connect only with devices that have already been paired.
When I start direct advertising, I get a app_error_fault_handler...
