Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Using: ncs v1.4.0, Modem FW v1.2.3, SES v5.10d
I have a custom nRF9160 board with code based on the Asset Tracker app. I have GPS triggering off of the accelerometer. GPS...
The PDK does not show up in file explorer. Power switch in VDD position. LED 1 is on solid. The device manager universal Serial Bus controllers does not list any device that...
Hi, sorry for adding more posts on the same issue, but I don't see any of the posts that speaks to my current situation. I'm using nRF51822 and SDK 12.3.0, and I'm trying...
I am using NRFSDK 1702. I have one NRF52840 as central and multiple peripherals. The central receives data from the peripherals and then transmit the received data via hardware...
Hello,
I am trying to create an application that uses the mesh light lightness [client/server] model using the example application as a guide and I have a few questions...
I want to check which version of BLE is implemented while using a particular SDK or Soft Device(SD). Is the version of BLE dependent on SDK or SD or both ? I couldn't find...
Hi,
We encountered a problem if we take off the battery during functionning.
The UICR Register is completly erase when we put back the battery.
The issue is with lost...
Hi - I have a MDBT42Q SoC board developed by Seeed Studio which contains the nRF52832 SoC. The board is powered as the image below and I can program the board through the...
SDK: nRF5SDK Toolchain: ARM GCC
Hello,
I have some devices out in the field using nRF52840s, using the non-SoftDevice bootloader, and a custom mechanism for reading updates...
While the nRF5 SDK offers great support for validating the SoftDevice and application firmware in internal NOR Flash on every boot, it looks like that's not the case for the...
I am using nrf52 DK board with SDK15.3.0 developing my application on top of ble_blinky_peripheral example .
How do add CTS service in my application ??
I have refered...
Hi
I want to make use of this SD-card reader together with the nRF9160dk.
From what I understand:
1. I need to create a nrf160dk_nrf9160ns.overlay file to chose which...
Hi,
As in the subject, I cannot find where to change the optimisation level. I am working with the Zephyr bluetooth sample project - peripheral_hr.
I have found a previous...
Hi
I have register the esim of iBasis and its works relly well but I need know how to use a esim of a different company on nRF9160DK, I don't know if the location is important...
