Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
We are using a custom ARM board which runs Linux and has a UART interface to a nRF9160.
I'm not how to phrase this exactly so I will just describe what I would like to do...
Hi,
I am using nrf51 DK and MDK is keil5
SDK : nRF5_SDK_12.3.0_d7731ad
softdevice : S130.
when i load the code nRF5_SDK_12.3.0_d7731ad\examples\peripheral\twi_sensor...
I have used light_Switch example from nrf mesh sdk nrf5_SDK_for_Mesh_v4.2.0_src I like to get the client source address in nrf_switch_server what should I need to modify to...
hello Nordic
i am using nrf 52840 dev kit, sdk 16.0
i want to make a sampling of 2 channels at 32MHz rate. the data shell be passed to RAM via easyDMA, after every 4...
Hi, I try to change my MAC address, but return error code 8.
check error code 8 is :
So I try set the mac address after ble connected. and the function sd_ble_gap_addr_set...
I'm trying to drive LEDs using PWM on Thingy:52 and Zephyr OS. It works when I connect external diodes to GPIOs, but built-in LEDs are connected to I/O expander instead. ...
Hello,
I have an Android application that sends and receive data from a nrf52832 peripheral.
During a test for our device using a nrf52932 chip, 2.4GHZ noise is emitted...
Hi. I bought the BM832E development board and have not yet ordered the DK board.
It says that arduino uno rev 3 is compatible with it. Does this mean I can plug my arduino...
Hello,
I am using nRF52 DK development board. I'm having a problem when I load simple blink example . I am getting an error message Error: Flash Download failed -...
Hi all!
Im still new to this and I'm trying to help a friend with a PCB design. We are using the nrf52832 and recreating the design from the reference circuit given in the...
I am trying to Compiling ‘ble_advertising.c’ and get 'NRF_EVT_FLASH_OPERATION_SUCCESS' undeclared (first use in this function).
This declaretion is already in the nrf_soc...
Hi;
i tried to compile LED Button app founded in this tutorial infocenter.nordicsemi.com/index.jsp in nrf51822 pca 20006 I had these errors someone can help me please or...
I just make some change Tx power level on "ble_app_blinky" app, i see that: when change Tx power(-20, -16,.., -4, 0, 4) like this code i mark red color below.
---------...
Hi,
I was trying to load the agps sample code into thingy 91 for testing. I read the readme document which mentioned that code is compatible with thingy 91 too.
After...
Hello everyone,
I wanted to start with Thingy:91 today, so I first wanted to update the device with the newest firmware.
First thing I found confusing is: On the Getting...
