Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi, I am looking where can I get the ACK from the light bulb, in Zigbee light control example. I am using the latest sdk nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.
what...
Hi,
The documentation for the simple_on_off model in the nRF5 SDK for MESH v4.1.0 states that the light_switch example uses the simple_on_off model.
The documentation...
I think spi slave pins should set as input but I want to control CSN pin as output in spi slave mode on nrf52840. Is it possible it?
I know that CSN pin is controlled by...
Thingy91 is useless without working samples and SDK
Out of the box it cannot associate with any NB-IoT cells here in Bulgaria. I tied using the provided SIM card from iBasis...
Hi I am having some trouble changing BLE connection parameters (mainly due to the connection handle). Is there any working example that I can refer to, which explains how...
Hi Nordic folks,
Our project is using nrf52840-DK boards as the development beds. We're developing a security application by leveraging the internal CryptoCell CC310 inside...
Hi everyone,
I successfully tested the example of the MQTT publisher in the IOT sdk on a NRF52840 and a raspberry pi 3+. The messages end up in my mosquitto install and...
Hi,
We have seen random ARM faults.
After some time we have seen that the lr register often pointed to entropy_cc310_rng_get_entropy.
This is our setup:
- Environment...
I recently purchased nRF52840 DK. While scanning through the website, I came across a suggestion to start with Blinky example. I opened the project in Segger Embedded studio...
Hi,
Observed that Openthread CLI project in NCS v1.3.0 is not compiling as it is using Segger Studio but building with command line. Please fix this.
Thanks
Sridh...
Hi Nordic experts,
I am trying to use Segger IDE to build the mcuboot boot-loader for NRF52x development kit. I am using NRF connect SDK 1.3.0 While I can build it successfully...
Hi
I am facing two issues in the below code. I use segger embedded studio.
1.The value I am setting as fs_initialized = true in line number 90 (inside FRESULT fs_init...
Hello,
I'm working with nRF5 SDK v16.0.0.
The documentation on Hardfault handler implementation clearly suggests to define DEBUG_NRF in order to get an automatic breakpoint...
I have the Thingy91 module, everything is working when I (turn off modem then) set AT%XSYSTEMMODE=1,0,0,0 (and turn on modem again), but if I power cycle the device the original...
