I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Good Afternoon,
We are using the nRF52840 DevKit with our BLE peripheral app and after connecting on iPhone (iOS11) and trying to read the RSSI (readRSSI() from CoreBluetooth...
I am trying to send data from a phone to the NRF51822. The data is being sent from the phone in 20 byte chunks to a write characteristic. When the event handler for receiving...
I have been working on a C++ library for the BME280 sensor to be used within the Nordic SDK and am so far only focused on using TWIM, Within this library I intend to use TWIM...
when i use the ble_adverting_start(BLE_ADV_MODE_FAST);
and then use the ble _advering_start(BLE_ADV_MODE_IDLE);
then ble_adverting_start(BLE_ADV_MODE_FAST); the return err_code...
OS ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit processor 28-pin Land Grid Array / 15GPIOs / SWD Soft Ver:nRF5_SDK_15...
I have implemented Legacy OOB on NFC and when my Android phone attempts to pair with the device, I receive a NRF_ERROR_STORAGE_FULL error in PM_EVT_CONN_SEC_FAILED event durring...
Hi, now I'm developing my projects(bt-audio-advertiser) with SDK 15.2. and Thingy:52.
I want to load PDM data to extended advertising packets. I succeeded to use extended...
Hi, now I'm developing my projects with SDK 15.2. and Thingy:52.
The projects are bt-audio-advertiser and bt-audio-receiver.
I adapted extended advertising to a Thingy...
Hi,
I have a problem making NFC (with a simple text record) work when I enable SoftDevice: I do not receive any NFC event and NFC communication does not work.
I have a...
Hello,
I would like to get the value of a temperature sensor, convert it from A -> D, send it to a server and then get it with a client (mobile application)
I need a sensor...
Is there any way to perform multiple DFU simultaneously using the single nRF51 dongle. I have to perform DFU from a custom application developed on windows PC. As I need to...
Hi ,
I am running example in nrf52840 using segger embedded studio .
And i am trying to define __no_init variant ,
May be sameone know what is the syntax . in IAR __no_init...
Hi all,
I am building a demo for Bluetooth mesh networking with thingy. I had followed the instructions under this link:
https://github.com/NordicPlayground/thingy52-mesh...
Hi,
I am using the twi_sensor example in the board PCA10056 with SDK v15.2.0. I am trying to disable the internal pull-up resistors of SDA and SCL lines to use external...
There appears to be a design flaw in the nrf_sdk_freertos code that produces a race condition. The race condition can result in a delay in processing a SoftDevice event, or...
