I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi!
In a Bluetooth mesh, we would like to get a feedback message from a group of nodes, via a reply message, after sending a message to the group.
The Bluetooth blog writes...
Hi. I am trying to get the peer address from of the peripheral my central has connected to within the BLE_GAP_EVT_CONNECTED event.
The following returns the address, however...
Hi folks,
I try to do create timer. Therefore i want to adding some files in blinky project. So here is some screen shot. Thats about debug error. First i used SDK 15...
Hi team,
I was asked by one of my customers, that if they can use nRF51822-QFAC (existing products design) as peripheral while connected by 2 central (Phone & Router)...
Hi I am a fleding embedded system engineer trying new ways to develop a process( Flashing) in my company,
My company's senior software has designed a control box which...
Hi,
I am facing problem while developing code for the application.
I am working on the "ble_app_uart" example code to develop my one of the application, But after making...
I'm using the code from Vidar supplied here . It works well, but shuts off after 3 minutes.
Based on the idle_state_handle brief, " If there is no pending log operation...
Hello,
I would like to touch on some problem we encountered when using the MPU9250 sensor.
Our goal in the project is to simulate the movements of the MPU9250 sensor in...
When I use the nRF connect app on android phones, the services and characteristics can be detected and controlled correctly, as below.
But when I switch to iOS nRF Connect...
I am using the nRF5_SDK_15.2.0_9412b96 for development of nRF52840. I have both the nRF52840 dongle and also the DK.
I find that I am not able to change the default Nordic...
Hello. I have build by application on nRF52832 based on ble_app_template example (SDK 15.1, softdevce s132 6.1.0). I've configurated Peer Manager library as it recommended...
i use nrf_drv_twi_init(&m_pedo_twi, &twi_pedo_config, ai_pedo_twi_handler, NULL) open I2C , sent data , then use nrf_drv_twi_uninit(&m_pedo_twi) close i2c, but power consumption...
I want to use nrf52832 SPIM， In nRF52832_PS_V1.4 it described that "An SPI master transaction is started by triggering the START task.Following a START task, the SPI master...
Hi there, I'm trying to download the latest nRFgo Studio (1.21.1) on the website, but using this version I cannot detect Nordic 52840. I notice that this package is using...
