Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi all
I'm working on a custom board using gcc and eclipse.
My primary problem is I'm fighting with the ld settings for the secure bootloader.
I activated the RTT which...
Hi,
I want to write calibration and configuration datas in to flash and read it back. By using sd_ble _flash_write API function , I can write up to 520 words(520* 4 bytes...
Hi, all!
nRF51822 had been used in my project, because of dual bank bootloader and softdevice, the
internal flash memory was not enough for the application. I want to...
Hi there,
I need to add more the function based on Bluetooth, and I need the better security of the function. However, I do not want others read flash data freely and I hope...
Hi
I'm preparing for some tests and I'm wondering where I can find information about what the expected percentage error rate should be?
Right now with 2 nrf boards connected...
Hello to all nordic jedi masters!
I have made an observation, on which I would like your confirmation.
My combo is: nrf52832 + SDK 11 + SD132.
Will my application ...
I'm currently writing my thesis, and my goal is to establish a network protocol like IP. We need to transmit about 200kB of data between 2 or more nodes once every 10-30 minutes...
I am programming a device with a NF52 that uses a hall effect switch o enter/exit sleep mode when BLE is in advertising mode. When connected, It will generate a separate BLE...
Hello,
i have a strange behaviour on a board with nRF52. The board is flashed with SD 4.0.2 and bootloader.
On Keil If i load the bootloader with JLink, it runs and...
I'm using nrfutil version 2.0.0 and have noticed a strange bug today when generating a new signed application image for bootloading.
If I have a version number of 0207...
hello , I am new to SPI protocol.I am using NRF52 DK &nRF5_SDK_13.0.0_04a0bfd( pca10040) using keil-5. I want spi master example code. Can any one suggested me where I find...
Hi there,
The S132 SoftDevice for the nRF52832 has grown in size from 0x1F000 for release 1.0.0-2.alpha, to 0x23000 for 5.0.0-3.alpha. It appears that the nRF52840 will...
I have a small PCB I'm prototyping/assembling, based on a nRF52832 with a few sensors. Looking for someone here to help me with writing basic firmware for testing the board...
