I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
If the softdevice is not used, As follows:
static void gpio_init(void)
{
nrf_gpio_cfg_input(Record, NRF_GPIO_PIN_PULLUP);
nrf_gpio_cfg_input(Play, NRF_GPIO_PIN_PULLUP...
There is an input clock signal with frequency of 3MHz-5MHz, but the exact frequency is unknown. I want to use nRF51822 to detect the clock signal's frequency, the accuracy...
Hi, I was using LG's HBS750 (Bluetooth Headset).
This device , after it is connected to an iOS device, shows the headset's battery level.
(Device Spec : Bluetooth 3...
Hi,
When running the multi-role-conn-observer-advertiser example on nrf51822 Soc with S110v7, I never be able to get the MAC address, and even the RSSI is always 0x1.I...
Hi all,
I am trying to implement a scanner (for reading RSSI and MAC address of the advertisor) , and I am based on S120\multilink_central example.
I understood from here...
I am trying to port the SDK 7.2 DFU example to support the S310 stack and compile using GCC. I have made the necessary changes as suggested in this post and I am testing on...
I'm using SDK 7.1, PCA10028 & PCA10003, SD310 2.0.1
My understanding is that the NFR51422 chip on the *28 board has twice the RAM, but otherwise is the same as the NRF51...
I'm using the nRF51 DK (pca10028) with the S130 0.9.0-1 ALPHA release and the experimental_ble_app_s130 example from Keil 5 doesn't work out of the box. Also I'm running 7...
This is Rajesh.C working for Sienna ECAD-Bangalore, India. We are using nRF51822 BLE in our design. I would like to know how many I2C and SPI device can be connected to the...
Hi,
I just receive a nrf51822 QFAC.
I'm using SDK 7.2 with Softdevice S110 7.1.0 with gcc.
If I compile using .ld from xxaa, It works (but using 16k RAM).
The same...
Hi, We have an nRF51244 and are using a single ADC in 10bit mode with a 1.8V supply (smooth regulated from battery) wired in LDO mode. The problem is our readings are all...
how many nrf 51 iot sdk devices can connect simultaneously to raspberry pi in your example setup...?
currently your device supports node role....when you will come up with...
Having just seen a couple of questions relating to DMA, which I was not aware existed on the nRF51822, I did a bit of digging, and it seems there must be newer silicon versions...
Hi all,
Please can anyone explain when the device_manager_event_handler() is triggred ?
And also, what difference between on_ble_evt() and on_sys_evt() and when they are...
Hi all,
I am using nrf51822, on pca10005 board, and debuging the s120/ble_app_hrs exple. I charged s120 v2.0 in memory.
The problem that I have is when ble_stack_init()...
