Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I am designing a battery-powered mobile device.
Previously, I was using Reg0 in DCDC mode, but I added an external 2.0V DCDC with higher efficiency (low Iq) and decided...
Hi!
I would like to know if anyone has any idea when we will hear more about the future products compatible with the new Bluetooth Core 6.2 specifications, as this will...
Backround: We are planning to use TF-M with a two-stage bootloader (NSIB & MCUBoot) using dual-slots for secure and non-secure images. We need to support configurable fixed...
To use ECDHE_RSA you need to enable the following Kconfig symbol:
This symbol depends on MBEDTLS_HAS_RSA_CIPHERSUITE_REQUIREMENTS :
This symbol depends on MBEDTLS_RSA_C...
I am developing a project for the Thingy91:X making use of the Asset Tracker Template.
Following the Getting Started guide, I successfully build for the Thingy91:X.
However...
Hi,
We have an existing nRF91 (nRF9151) project (NCS 2.9.0 ) that already includes multiple modules such as ECG, external flash, RTC, modem, etc. Now we want to integrate...
Hi Team,
I would like to interface the nrf9160 with nrf7001 by using the SPI. While building the WIFI-Scan example by using SDK 3.1.1. Even by using WIFI-shell example these...
Hi team,
I am experiencing a persistent MPSL assertion 1519 on nRF54L15 that occurs consistently at ~5 seconds after BLE advertising starts. The assertion indicates that...
Hi everyone,
I’m using nRF9151 with nRF Connect SDK 2.9.0. Without changing anything in overlay, prj.conf, or source code, several of my projects suddenly started failing...
Hi Nordic DevZone,
We recently acquired some Pro Micro nRF52840 Dev Boards ( link ) and were looking to use them with the nRF Connect SDK. The boards use a UF2 bootloader...
I have a question about the nRF54L15.
１．I would like to know the maximum number of devices that can be registered for whitelist and bonding.
２．I want to know how to...
I am having an issue where my nRF52840 Development Kit is not being detected by nRF Connect for Desktop , specifically in the Quick Start and Programmer apps. The DK does...
Hi, I have an Adafruit Feather nRF52840 which I'm programming using SDK 3.1.1. I want the following UART config but it is being rejected with error -134 which I believe means...
Here is a professional and technically detailed ticket template you can use to submit to Nordic Semiconductor (DevZone) , Quectel Support , or your internal System Architect...
Dear Nordic,
Could you please guide us how to set HCI_LE_Transmitter_Test / HCI_LE_Receiver_Test command?
Do we have to use Test mode command too?
Thanks.
