Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I'm trying to use the nRF Desktop project as a base for our project, prototyping on the nrf54l15dk_nrf54l15_cpuapp board target. I have an overlay file defined like this:...
Error Report:
When flashing, I get this error:
Error:
One or more batch tasks failed: * 1050058878: Timed out waiting for response from worker. (Generic) FATAL...
Hello Nordic Team, I have referred this post and am aiming to create an empty bare metal project on nrf54L15 for BLE peripheral with GAP read, write, notification and idicate...
HI
I am currently using nRF54L15 with NCS 3.0.0 SDK, running the periodic_adv_conn example. I made the following modifications to the extended advertising and periodic advertising...
We have noticed an issue with our device built on nRF5 SDK + nRF52832 when connected to iOS 26.
Initially after connection, everything is ok. Then we attempt a connection...
I am porting nRF SDK 2.6.1 to SDK 2.7.0 on the nRF5340. For the network core, where exactly should the kconfig (prj.conf) file be located and named? On the sysbuild migration...
Hi, based on the previous struggle with data transfer drops with nrf9161 ( ) we came after the cooperation with Vodafone MNO to the situation, that (at certain test place...
I'm using the peripheral_bms project. The only change being in the overlay to make it work with nrf52833 dk. I'm able to connect with nrfConnect and see the services (except...
I'm developing with the NRF52840 using IAR Embedded Workbench , and implementing wireless communication based on the IEEE802.15.4 Zigbee protocol .
In the MAC frame layer...
I am new to Nordic and want to design with the nRF52840. I have read this guide:
used AppCAD to find the best width and clearance for the ground layer, but when I downloaded...
Hello, I am using NCS 3.0.2 on nRF52840. I have been using MCUBoot for a long time on my device, and it is working fine. Recently, I went through a requirement where I needed...
Hey everyone,
I've been trying to get the Bluetooth Mesh DFU Target sample working on my nRF5340 DK and running into some issues. I've read through the docs.nordicsemi.com...
Hi All,
I have an nRF5340 Audio DK which has problem with the network core. When I connect the USB to board or try to recover the board the MCU light at the bottom of...
Hello all,
I am working on a project with 2 nrf5340 Audio DK's and I want to have the same functionality of the walkie talkie demo but instead use the microphone of the...
