I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello ,
I want to use OLED display having SSD1351 driver with nRF52832 DK board over SPI. Is there any library or support available ? Please help to share if it is available...
Hi,
We have a peripheral based on the nRF52840 which connects to a smartphone as the central.
Following the guidelines for iOS we have selected a connection interval of...
Hello Devs,
I am testing an nRF52840, configured to operate to 1.8V using the DCDC converter. All pins are supposed to operate in a 0-1.8V range.
So my question is...
Using 52840, I would like to drive an external device at 800Khz
Works well without enabling the SoftDevice
But once the SD is enabled - this does not work
Ideas?
I used 9160 to develop a product for the customer. Previously, I used ncs1.2.0 SDK, and the power consumption of the whole machine was about 200uA. Now I am going to use ncs1...
Hi mate,
I followed the link (+) Add DFU support to your application - Software - nRF Connect SDK guides - Nordic DevZone (nordicsemi.com) step by step and its worked...
Hi mate,
I followed (+) Add DFU support to your application - Software - nRF Connect SDK guides - Nordic DevZone (nordicsemi.com) your instructions and successfully implemented...
We found that when testing the nRF52832 chip, if the C9 capacitor is empty, the chip broadcast power consumption increases from 20uA to 40uA, and the power consumption of...
Hello,
Over the years we've occasionally been experiencing a issue with nRF52840 and nRF52832 chips in case of which any BLE activity would stop happening. A chip mounted...
Hi,
I've used the module https://github.com/NordicSemiconductor/cloud-firmware-ci-device-helpers-js to create device certificates for a nRF9160 device and then AWS JITP...
Hi there,
Is it at all possible to run nRF Connect for Desktop apps like the programmer and the power profiler from outside the nrf connect for desktop app?
e.g. is there...
Good day,
is there a way to check if a client is connected to GATT server/service? Would like to send a data after device gets reconnected.
i am using PCA10040 with...
Hello dear Nordic. I am wondering if I can simulate a hardware event by the software by writing any value to the event register, or in other words to create artificial interrupt...
Hi,
I implement the CLI on my nRF52820 and I see in function cursor_next_line_move in file nrf_cli.c they use "\n" but for my project I don't want to pass in cursor_next_line_move...
