Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0 I could build with NCS v1.9.1 but I cannot build with NCS2.0
[Build log] In file included from C:/NCS200/v2.0.0/zephyr/include...
I have an Ellisys Bluetooth Explorer 400 sniffer and am trying to sniff the ISO audio data between nrf5340 ADK boards. I enabled CONFIG_BT_LOG_SNIFFER_INFO, CONFIG_BT_DEBUG_KEYS...
Hi there. I am trying to utilize both the network core and the application core to perform two separate tasks at the same time. I have looked through some of the sample projects...
Hi, I need to setup a vendor specific class USB device driver. The driver shall present the following data endpoint:
0x84 for Bulk IN endpoint 0x03 for Bulk OUT endpoint...
SEGGER Embedded Studio for ARM can't connect to nRF52832 device. But J-Link RTT Viewer can connect to nRF52832 device. The following is log messages of J-Link RTT Viewer....
Hi there,
I am currently developing on the nRF5340DK and am doing some very processor-intensive work (@ 128MHz) on data read from the QSPI bus. I would like to set up non...
Hi, I have been trying to build an example of console usb example and then build it for thingy91_nrf9160_ns but got an error :
I have been trying this code several weeks...
Hi, with appropriate pm_static.yml and dts.overlay we managed to setup a LittleFS instance over external flash. However this broke the Settings storage subsystem the BLE stuff...
hi support team,
for our sdk17.0.2 demo hid_keyboard, i tested it and using IOS mobile to pair with our 840dk or 832dk
find out after lots of reset the keyboard device...
I am developing an application that uses nRF52840 wake on NFC, and spends most of its time in system OFF state with NFC wake enabled.
Per the nRF52840 Product Specification...
On the NRF52840 dongle am building a protocol on USB CDC ACM.
Using app_usbd_cdc_acm_read to read one byte at a time works perfectly.
However, I can seem to make app_usbd_cdc_acm_read_any...
Hi,
I am developing a wireless product in which i want to use nRF52 in ESB mode.
The product is battery powered and should be sleep mode.
What i have decided to do is...
Hi,
I have read the thread here: which implies that this config option might not work?
Does it work? I would like to build mcuboot and then always use the same binary...
