Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
I am attempting to merge two example programs together and have hit an issue with a hard fault when my timer interrupt triggers.
This works fine in the standalone...
I refer to https://github.com/alc6/nrf52-pc10040-multiperipheral-passkey/blob/master/main.c for implementing static passkey. But pm_sec_params_set() returns errCode=0x7. ...
What I've done
1) Set up ot-br on an Rpi4 by following this guide .
2) Set up a 52840Dongle (plugged into the RPi4) as RCP by following this guide .
3) Installed the...
I'm using SDK 14.2.0.
I'm trying to read the device ID register from ISM330DHCX accelerometer this way:
ret = nrf_drv_spi_transfer(&m_spi[Instance], ®_addr, 1, read_temp...
Hi guys,
So lately, I decided to update the sdk from 4.1.0 to 4.2.0 and there are some problem that I can not solve myself. So I use the macro ZB_ZCL_REGISTER_DEVICE_CB...
Hello,
i've trying to update the codebase of our current project (under development) from NCS 1.9.x to NCS 2.0.x.
I'm experiencing hard fault crashes when I try to perform...
Hello,
I'm using SDK 17.0.2 with S113, v7.2.0 on the NRF52840. We currently have an instance of CLI running in our executive loop, and it works fine. We'd also like to implement...
I facing the above issue when build a project. The project structure is below. I copied the Git project project to d:can/firmware/zephyr/samples/drivers/can from https://github...
Good day Nordic people, I am facing a problem when erasing or writing to internal flash memory after enabling softdevice. here the details and tests: Setup: - GCC, arm toolchain...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I managed to implement a multilink communication...
Hi Support team,
nrf5 sdk for mesh 5.0, nrf5 sdk 17.0.2, s132, SES;
We are trying to understand the LPN feature based on the LPN example because in our scenario there...
We're developing firmware for a custom board that uses the NRF5340. Today one of the developers reported that they were no longer able to communicate with the board over SWD...
Hello, all
I built CLI sample for Openthread, but failed to run, windows 10 couldn't find any nrf52840dongle inserted, and not any log output through RTT.
When I debugged...
Hi guys,
i'm using DFU over serial and i get the error 4 in NRF_DRV_UART_EVT_ERROR.
This was not happening before and suddenly started.
What could be the issue?...
