Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
hi
I would like to use BLE Mesh to control my products. I would like to build a mesh network in advance, install a provisioner and automatically provision the nodes when...
I'm working with a lwm2m client using t he LwM2M client utils library to connect with a lwm2m leshan server.
Everything works great with LIFETIME = 30sec (default setting...
Hi:
There are two BLE architecture can be used on the nRF5340:
Split the Bluetooth LE Controller and the host part of the Bluetooth LE stack and run them on different...
Hallo Team,
I am using nrf45340 Audio DK to evaluate Bluetooth LE Audio application example.
For experimental purpose, I am using SBC codec. I have been following instructions...
Hello Nordic support:
We encountered a problem when downlaod the firmware for the nRF9160 with jlink nrfjprog program. Most our nRF9160 module can download firmware OK just...
Hi Nordic Team,
Working Environment:
nRF52832 DK, nRF17.1.0 SDK, Keil uVision 5 IDE, Windowns10 pro PC.
I am working on ble_app_uart.c Peripheral example.
According...
Hello,
the git version in ncs\toolchains\v2.0.0 isgit version 2.26.2.windows.1!
That prevets me from using git credental-manager-core in nRF Connect 2.0.0 console in Visual...
Similar to t_m's post here (only in a different SDK), I am trying to generate two PWM signals (motor1_fwd_pwm & motor2_fwd_pwm) in 180 degrees phase shift in respect to each...
Hi,
We have developed the firmware code for a system using nRF52832. We would like to keep the same system but switch the SoC to either the nRF52840, nRF52820, or nRF52833...
Hi there,
I am trying out the nRF Connect SDK v1.9.1 with a custom board (with an nRF52833) that we have produced. I have set up the necessary plugins in VSCode (v1.67.2...
I have two boards, a Thingy91 with "nrf9160 SICA B0 1924AP" and a nrf9160dk with "nrf9160 SICA B1 2110AM". Everything works as expected on nrf9160dk but on the Thingy91 shell...
I create an app timer for spi communication at 1s.
The I noticed a strange phenomenon.
You can see the 13uA is in sleep mode, when the app timer timeout, CPU wake...
Hi All,
I had a MCU to connect nRF52840 via UART and nRF52840 is used for BT central function.
I need to know the command to control nRF52840 and what function should...
