I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I have
Hardware: nRF52840 DK - 1 nRF52840 Dongle - 1
Software: nRF5 SDK Mesh - v5.0.0 nRF5 SDK - v17.0.2
I want to program Mesh Serial example on nRF52840 Dongle using...
I try to using nrf_fstorage_write() to write data to fstorage and then waiting writting finish. But it hang at sd_app_evt_wait().
int _fstorageWrite(const uint32_t addr...
I try to integrate https://github.com/NordicPlayground/nrf5-calendar-example into Keil project. But the following error messages shown when accessing NRF_CLOCK.
error messages...
Hello.
I have a question about programming a dfu + softdevice + app code using j-link.
I programed like below for using wireless firmware update.
program softdevice...
Hi,
in my application I have setup the nRF52 to wake-up from deep sleep if a low value is detected on either of two GPIOs (4 and 5). What I'm trying to achieve, is to be...
Hello,
with my nrf52dk board i had made some tests to check the scan performance.
Using nrf Sniffer - with Wireshark
nrf Mesh - LightSwitch Client (Mesh SDK v4.2...
Hi,
Automatic installation from ToolChain Manager, no errors. Perform west update ,no errors. Check all the files ,no problem found.
Have reinstalled NCS for many times...
Hi,
Using MeshSDKv5 on custom nRF and nRF52DK
We are working on an LPN wireless PIR sensor so which sends a sensor status publish message on occupancy.
I have notiiced...
Hello,
I want to keep perform some task periodically .. probably using tick timer / rtc / application timerof every 5 ms, to perform some task, without keeping the thread...
Hi,
I am transferring 100 bytes of data via BLE-Mesh from a vendor client model, which I need to receive in my vendor server model.
I referred to nCS provided chat sample...
I am trying to implement an already made sample from Nordic for INA219 sensor. As always it didn't work initially and showed many errors even though it was a sample code but...
Hi. I wanted to test the power consumption of the NRF5340 when using the Bluetooth low power feature. Using the Energy Profile Kit seems convenient but I am not sure if the...
I'm using a sample from nRF connect SDK v1.91.1 for BLE peripheral. I'm trying to read one of the buttons on the development kit, but I'm not very sure how to use the button...
Hello everyone,
I'm trying to play with PPK II to check current using ble_app_uart example (nRF5_SDK_15.0.0). I notice that the nRF52 DEV KIT keeps advertising and if there...
