Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi there,
I faced this issue while I was setting up a test through two UART0 & UART1 ports on NRF5340 chip, using baudrate 1000,000.
Here is the setup:
UART0 &...
I currently use nrfConnect on android to download firmware to nrf52832s. I am just getting started with nRFUtil and the dongle.
If I understand correctly, I should be able...
I have a nRF52 DK from DigiKey that I've been evaluating and I ran into an issue: I had a custom app that was talking through Bluetooth and sharing some custom characteristics...
Hi, I'm using NXP LM75B temprature sensor based on nRF SDK's example code.
I would like to save power on this sensor.
I have prepared the code as follows:
Following...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
I'm developing for nRF52832, SDK 17.0.2 and softdevice S312 7.0.1.
After I upgraded from Segger Embedded Studio 6.22a to 6.30 I found that turning on any compiler optimisation...
HI DevTeam,
I'm using the nRF52840 as co-processor due to the semiconductor shortage and I don't need to use the RF section. What should be done with the antenna pin in...
This is the implemenatation spec for GATT server database (reader) firmware i am working on.
I have implemented advertisement packet using nRF Connect SDK latest.
Not...
Hello,
I am customizing the BLE DFU bootloader for nrf52820. Integrated an LCD to it.
Now I need to display the percentage of firmware download on the LCD. It will take...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832. I want te retrieve data from a battery cell monitor which uses the LTC6804 from Analog Device.
...
Hi,
I need to capture time in nanosecs between 2 tasks, for which I am using the zephyr suggested time measurement code as in:
When I am trying to compile the above...
Dear DevZone,
our goal is to replace the RX side of an old system, which is using the nRF2401. For real-time capabilities, the Shockburst protocol was employed.
Reading...
Hello, Nordic Engineer
I use nrf52811 and SDK 15.3.0
In example 《ble_app_uart》, I added timeslot（ESB）
Run this code《nrf_esb_write_payload(&tx_command);》
Subsequent...
STEVAL-STMDLTE WITH NRF52840 using UART
We are trying to integrate the STEVAL-STMODLTE Link chip into the NRF52840 for rapid prototyping.
Trying to interface nrf52840...
