Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi, There is code for vendor model element creation in nCS provided Chat client sample, as in below:
This works fine in "model_handler.c",
But when I import the same...
nrfjprog checks the target for 0xFFFFFF before attempting to write.
It should be successful not only if attempt to write the same value as is already present but also
...
Hei, jeg evalurere et Reinsdyr projekt der 30 Reinsdyr skal løper inne i en binge, er det mulig å motta kun beacon fra BLE taggen i nRFAPP fra de 30, hva er max antall når...
Hi!
Using the nrf5340-DK, I am preparing a code to be used on a custom board, where the pinning configuration will be different from that of the development board. I have...
Hi
I am using the nrf Connect extension in Visual Studio Code on a Window 11 machine together with C:\Nrf_Connect_SDK v1.9.1
After having installed the nrf Connect extension...
Hi,
I am working with nRF52832_dvk board, i am testing the OTA example as per in this link. https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts...
Hello, I'm starting to design the pcb for the nrf52840. I looked but I saw that it is also possible to create it on two layers instead of four as the reference design teaches...
Hi,
I am trying to burst read FIFO of ADXL362 with zephyr adxl362 sample. 1 byte tx (read fifo command) and n byte rx ( reading the fifo data);
Zephyr is the last version...
Hi,
We tried to use Connect Interval 7.5ms with MTU 88B, both central and peripheral role are 52832, but observed disconnection after 30 sec.
Disconnection reason is 0x13...
Hello all,
Background: -NRF5340 -NRF SDK 1.9 -Zephyr 2.7.99
My objective is to send a data of 768 bytes by BLE. I use 4 notify to send this 768 bytes data (192 packets...
Hello,
I'm working on an application running on the nRF9160. The application is build on the Fanstel BLG840X and the code is shared between both the 52840 and 9160 on the...
Hello!
I have a problem updating network core firmware through MCUboot when NSIB is enabled (through "CONFIG_SECURE_BOOT=y" in my application prj.conf).
Without NSIB...
Hello Support, I'm looking for reference schematic for the interface between nrf52840 (or similar) and the nrf21540 . Is there a simpler version than the developer kit user...
Hello again,
I'm trying to lower the power consumption of my thingy91 by turning off the serial by setting config_serial=n. Unfortunately, this causes a crash while running...
