Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
So we have a project where we use the NUS, and we need to detect when a client subscribes. We eventually found a way, but it seems very obtuse and a bit black magic...
Hello,
I'm working on a BLE application using zephyr and nRF Connect SDK 1.8.0 on the nrf52840. I'm debugging the BLE stack using ozone but whenever I set breakpoints the...
My Current nRF Connect SDK version: 1.5.0
I am trying to follow this reference https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.5.0/nrf/samples/nrf5340/netboot/README...
I am working on Apple Macbook Air with M1 silicon and I installed nRF command tools version 10.15.4macOS
When I open the toolchain manager , there is an error that shows...
Hi
I'm using the GNSS sample. It gives me an output, but I want to interpret the output of it. How can I read this and translate it to coordinates?
Kind regards
Sarah...
Hi,
I installed nRF Connect SDK (1.9.1) using Toolchain Manager v0.10.3, and nRF Connect for Desktop v3.11.0. Before that I also installed NRF command line tools 10.15.4...
hi,
I want to build and flash only mcumgr bootloader code to my controller , from the example which i observed i am getting that mcumgr is always with some other example...
I use an InsightSIP ISP1907-HT module, I have a 4 layer board to minimise cost. Signals on top and bottom with GND on inside.
I'm concerned that my design could fail emmissions...
Can using whitelist on Central and Peripheral reduce the connection time? In my example I want to advertise every 3secs and want to make sure that the central connects to...
I am completely new to this toolchain and how it works.
I was trying to add a UART sensor to the matter sample project on the nrf52840dk. Is there anyone who can help me...
Hi,
What's the maximum throughput for nRF52832 as peripheral?
S132 7.1 SDS demonstrates configuration for 192kbps. But I noticed that DLE is not yet enabled. So can...
I want to use the timer to measure the interval between two signals, which requires an accuracy of 1us. But in Timer mode, I don't find a register that can read the current...
Hello Nordic semi team,
I am running into an issue with sd_ble_gattc_read
I have set the MTU size to 70 and I do this:
// Configure the gatt MTU size . memset(&ble_cfg...
Hi,
I'm currently development firmware for a application using a Nordic chip. This application will use some drivers allowing the communication with sensors and for the...
