Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
We need a bluetooth BLE module, for UART communication with AT command.
with certificatation EN300328 V2.2.2. Do you know where we can buy them?
If we use the...
we are using nrf52805 after in few devices sometimes BLE is not visible(stopped broadcasting) to the receiver.
Here are the observation on that faulty device:-
1. Device...
Hi Team,
we are working on smart remote 3 implementation using nRF52832 with Windows 10 pro operating system.
we tried to connect this remote with laptop using the...
Hello Devzone,
With an nRF9160 based project and lowest power, lowest current consumption in mind, is there an explicit I/O pin setting to make via Zephyr API for the nRF9160...
Hi
Now I am using NCS1.7.1 for development the nRF52840 chip.I need to use the C standard library(math.h).I set up as follows:
There is no problem when the above macro...
Hi,
I would like to know the functioning of CPFD (I would like to represent the characteristic value as IEEE754 float32) I am not aware of how can I implement this. for...
I am using an nRF52840 and communicating with an ESB. Packets are sent one-way from tx to rx every 1 ms.
What is the conversion of RSSI to dBm?
In the data sheet, as ...
Hi,
In one of the ble example , it is using generic on_off_srv.c and .h files. along with health and generic server. we have requirement that we need to write unit test...
Hello, as stated in the Title im trying to establish UART Communication betwenn a nRF52840 DK and a nRF9160 DK. I need to use the Asynchronous API otherwise there are no other...
Hi Team,
we are working on smart remote 3 implementation using nRF52832 with Windows operating system.
we want to implement NVS. how to do with Windows OS?
I need to define a function to print message and register to other module. In my application, NRF_LOG is used by most modules so I need to use NRF_LOG to construct this printf...
Hi,
I tested Extended advertising for my data using sdk connect 1.9.1 and 1.8.0, the code is attached.
With both the SDK, I observed different behaviour. First of all...
I am running segger embedded studio 5.63a on NRF52832 and 52840 using SDK 16.0. We want to update SES to the newest tools compatible with SDK 16.0. We loaded version 6.22a...
Hi
We have some production equipment still running windows 7. We would like to update the nrf51 dongle to a nrf52 dongle.
But drivers for nrf52 dongle is not installed...
