Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I want to compare the RTC's counter_get_value() ticks with the internal clocks k_uptime_ticks() ticks. The problem is when the RTC is connected with our nrf 52840...
Hello,
While programming my board with a merged.hex I sometimes see some differences at the end of the Programmer log.
Sometimes the log ends like this,
2022-03-25T14...
Hello guys,
I am having problems on addressing an issue with my firmware. Maybe someone can assist me to find out the root cause for this, because I don't understand too...
Hello,
We buy nRF52832 chips and use them integrated on our own PCBs.
Our devices are small BLE devices to which your phone, computer, anything can connect to.
They...
Hi，
Would you provide the software of NRF52832 ESB communication with NRF24L01 ? And share the two Demo Boards PN for NRF52832 and NRF24L01. Plan to buy the DEMOs.
...
i study in derection of DOA.I now can get the iq sample from my Putty in COM PORT.i use NCS 1.9.1.I build and flash in my two boards with nrf52833.i use the cammand line tool...
Hi,
We came close to occupying all available flash memory in the nRF52833 board:
Memory region Used Size Region Size %age Used FLASH: 185620 B 187904 B 98.78% SRAM:...
Hello,
I have some issues with activating the gps-module for the "second-time" through mqtt.
See uart logging below.
First GPS attempt works, socket is created successfully...
Hi,
I was thinking of buying a Power Profiler II, but was wondering if it is possible for the profiler to measure the consumption of the chip itself or does it measure...
Controller- MDBT40 (nrf51822 based)
Softdevice - S110
I have an application where data comes from UART and have to send over BLE simultaneously. When I initialize the...
Hi there,
I have a problem to implement the SPIM in the Network core. I cannot detect any signal from SPI_SCK & SPI_MOSI by oscilloscope and logic analyzer (no signal from...
Hi,
I'm using VS Code to develop an application based on the Zephyr iso_broadcast sample.
How do you edit prj.conf? If I select prj.conf in the Explorer pane, then click...
Does the nRF52840 support Bluetooth low energy power control? I am using raspberry pi, running Raspian, kernel version 5.15.30 and I am specifically referring to the product...
Hi support team:
I develop my project with sdk 15.2.0 on nrf52832. Now I met a situation that I might need to call app_timer_start() again before the same timer is timeout...
