I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I'm trying to determine how to get a Linux timestamp for a project using nRF9160. It looks like the mktime() function is not supported. Any suggestions?
thanks!
I'm running into a weird bug where the first 4 bits received by my SPIM are always 1 - the next 64.5 bytes are all correct though... I've built 3 FWs out of provided examples...
Hi guys,
I have developed an app to read data from some sensors and notify the central with a frequency of 100Hz. It seems to work but I would like to share my approach...
Hello,
We are trying to get UART communication between nRF9160 and MSP430.
MSP430 need to send out a sensor data through UART.
We are using 1.9.1 SDK, and Visual...
Hi,
Is it possible to remotely execute a command that would force a BLE node into indefinite sleep or standby mode?
I am working to build out a BLE mesh network, where...
Hi. We have a custom board featuring 4 FSR sensors on it, based on the Nrf52810. Initially i tested those boards and the sensors using an STLink-V2, along with the Arduino...
hi thanks for you heip!
i want use \nRF5_SDK_17.1.0_ddde560\examples\peripheral\radio_test for radio test, here is the questions:
1、could this example can send prbs9 wave...
Hello!
I have to decode signals from two quadrature encoders. I know nordic has a driver for this, QDEC, however. there are a couple problems:
1. I need to control two...
Hi
Is there some example, how to use CAF and sensor_manager. I try to use BME680 sensor with CAF, but i'm somehow stuck. I got the sensor manager working and I see sensor...
Dear, I copied the Button sample project to another drive i.e. G. I added the overlay file. The file is attched. The included file is shown on ltop left corner side under...
Hi!
In my device,I make a master to connect a slave，in the NRF5_SDK，all examples for client are initialize with the service uuid.The questions is when the master don't konw...
The Socket AT commands documentation found here does not match the actual responses we're getting when we the run the commands on the modem through LTE Link Monitor application...
Hi Nordic Team!
I'm trying to configure device tree to add support of MX25L6473E for my custom board.
I have successfully configured it to correctly read the jedec-id...
Hi,
I have an NRF52-DK, which works fine. I'm developing applications for external modules, obviously, and am currently programming them with the DK on-board programmer...
Hello,
We made a custorm project using the nrf52832-ciaa-r. We made some range test and we noticed that the more we wait connected before doing the range test, the further...
