Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi everyone,
I would like to measure the total current consumption of the board in order to get an estimation of the battery life. I am using PPK-2 and nRF Connect Power...
Hello Everyone,
For my project, I have to make my BLE device to advertise itself for a period of time and transit to "scan" mode to scan for other device for a period of...
I am getting this fault when i try to run a observer handler where i have implemented semaphores.
And i cant figure out what this error code means
Thanks in advan...
Hello,
I am currently trying to run this ble_secure_bootloader . I am using SES V5.68 with the nRF52840 SoC and I am using nRF5 SDK version 14.2.0. I have also adjusted...
Hi Team,
I want to know the time with time resolution milliseconds for initialization time of nrf52840 chips and nrf52840 DK with external supply model?
KInd regards,...
Hi,
The below code I believe is in error. The below write operation overwrites the LIO2, LIO3, WIPWAIT, and WREN settings in the CINSTRCONF register by only writing the...
First off, It's great you guys are setting a high pace with development and improving the SDK but I and I think many other people would like it if you change a full version...
Hi!
I am currently working on this sample with an nrf52840 board and a nrf52832 board:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/peripheral...
Hi All!
Hope you are doing well! I am using nrf52840 and nrf58233. Is there any example available for both transmitter and receiver for connectable coded PHY beacons?...
I am trying to determine the best way to debounce 7 digital inputs with 2 bounce times ranging between 50 ms to 2 seconds. I thought of using the GPIOTE but that seems to...
Hi All,
I asked this question before but I accidentally pressed close.
The engineer told me that f or nRF5 SDK ( I assume as you said Segger), you can send 10 byte long...
I'm working with the project based on nrf52833 and SDK 17. I've noticed that when there are no devices on I2C bus, the application stucks on nrf_drv_twi_tx function, and the...
Hi , I'm using nrf5340 and nrf connect sdk 1.5.1 , recently I found out when sending large amount of data with low RSSI through bt_gatt_notify_cb the system would enter some...
Hi. I am using the Nrf52DK to program our custom Nrf52810 based board for DFU . We use the: nrf5sdk v17.0.2 with softdevice s112. along with the pca10040e_s112_ble example...
