I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I’m developing an ESB-TX program using NCS v3.1.1 . Previously, I had developed an ESB-RX program using nRF SDK 17.0.2 . Now, when I use the TX code from the NCS SDK to communicate...
Hi,
I'm new to embedded development but have experience in desktop C/C++ development mostly with Visual Studio.
I'm struggling to get my head around how I would create...
Hello,
I am trying to define a pm_static.yml file which will use the 512K ram on the nrf7002dk_nrf5340 for the TFM ram section.
I cannot compile the non-secure nrf7002dk...
Hi, I got my nrf54L15 DK, but i can't start RTT logging. I set this configs:
CONFIG_PRINTK =y
CONFIG_CONSOLE =y
CONFIG_RTT_CONSOLE =y
CONFIG_UART_CONSOLE =n
CONFIG_USE_SEGGER_RTT...
Hi,
Is there any ongoing development for a PPK3 ? If so, what is the timeline for its release ?
Some features requested in previous posts:
- Voltage measurement
-...
Hi,
Could you please clarify why there is an override of the checking rules in https://github.com/nrfconnect/sdk-zephyr/blob/ncs-v3.1.1/drivers/timer/Kconfig.nrf_rtc#L6C8...
We are developing a custom board with an ADC device that supports QSPI. Our application requires throughput speeds only available using QSPI.
All the available driver examples...
Hi,
I would like to use existing development setup (for STM32) :Visual Studio 20XX (not VS code) with VisualGDB plugin to work with the nRF9151 Development Kit.
However...
Hello, I have a project implementing the ASYNC UART API as laid out in the Nordic Development academy exercise. I had this successfully communicating with an external device...
Hi,
I run a couple test with the PPK2 on our board to measure and optimize the power consumption, but I had some weird results and I'm hopping you can help me out to understand...
Hi,
I am looking at setting up some of our team with the ability to flash our custom devices that contain various chips (nrf52, nrf53, nrf91). Assuming the SEGGER software...
Hi,
I can't program nRF52840 dongle using Programmer Tool on Linux.
Dongle is visible, can be selected and memory content read without any problems but file write attempt...
Hi nordic support:
Our product used nRF52840 and nrf5_sdk_17.1.0. It's inconvenient to connect UART port when perform DTM test to testing nRF52840's RF performance. Could...
Hi there,
I hope this message finds you well!
I’ve been developing several products using Espressif’s modules that offer both Wi-Fi and BLE on a single SoC. I wanted to...
I'm developing a custom board that uses the nRF54H20.
The Getting Started guide for the nRF54H20DK explains how to use the pre-built BICR file and program it to the chip...
