I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
I try to run Azure_IOT_Hub without HUB. I have set in prj.conf and prj_qemu_86.conf:
CONFIG_AZURE_IOT_HUB_DEVICE_ID= "mydeviceID"
CONFIG_AZURE_IOT_HUB_HOSTNAME="mydeviceIOTHub...
Hello,
NCS1.9.1,nRF5340DK,Windows10 X64,VSCode,
why frequent problems of "west flash --recover",
some time run cmd " west flash --recover",it will be ok,
and some...
Hi,
I'm trying to wrap my head around doing some basic GPIO reading, writing etc. and hopefully some interrupts. Apologies if these are basic questions - I've only really...
Hello dear People,
I would be very happy if anyone has an idea how to solve this.
The Problem is the following: I am using nordics lte link controller to connect to nb...
Hi,
1.) I am programming a custom board based on NRF52833 using NRF52833-DK using SWIO/SWCLK interfaces using Segger Embedded Studio with NCS v1.6.1. I am trying to print...
1. Your documents mention only SPI3 and SPI4 are available in non- secure mode.. which means spi-0,1,2 should not be available in non-secure mode.. But if i use nrfx drivers...
Hello.
It is under development using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I'm currently considering Flash Data Storage (FDS).
As settings, "FDS_VIRTUAL_PAGES...
Hello.
Target nRF52832( nrf52dk_nrf52832)
SDK NCS v1.9.1
Build : SES for win 10 (5.68)
1. Support BT5.3
My project used nRF5_SDK_17.1.0_ddde560. Recently I found...
I am using a custom board design with a Nordic nRF52832 and have implemented the Nordic time sync algorithm outlined here ( https://github.com/nordic-auko/nRF5-ble-timesync...
Hi everyone,
I'm currently using nRF52832 with nRF5DK_V17.1.0 file.
I understand that this question has been risen up quite a lot however, I still do not understand why...
Hello Nordic team,
I am testing a timer using code snippet which Nordic team recommended as a reference. My code is something like this:
uint64_t start, stop;...
Hello,
A nrf52840 central device programmed with Soft-Device S132 and connectivity firmware, the host is interfaced via USB and uses PC-BLE driver API's to communicate with...
Hi,
I'm using nrf52840 DK and android based mobile with nrf connect for mobile app installed.
I would like to execute a freestanding sample code to transfer message between...
Hi Nordic,
I met a issue on BUS FAULT , which caused by queue.
It core dumps that:
[2022-03-22 15:35:12.657] [xxx]index = 6,len = 158 [2022-03-22 15:35:12.660] [xxx...
