Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Hello!
While looking at examples and trying to work on the nRF52832 with sdk 1.8.0 I am noticing there are varied uses of functions with and without the _dt at the end....
Case 1: Using nrf52832, solder bridge cut: what current values do the PPK gives : is it of the entire dev kit with all peripherals, programmer and BLE Soc or does it measure...
Hi, I'm attempting to migrate from SDK 14.2 to 15.2, and am encountering a problem with the crypto/rng module whilst trying to utilize micro_ecc.
(code being shown in order...
Soo,
I've had a sim and a device connected to the nrfcloud, it worked. Then I didn't use nrfcloud for a couple of months, and now it doesn't work anymore. It tries to connect...
I am using nrf52832 dev kit and soft device s132. I have use my board as peripheral
and i have another nrf52840 dev kit which i am using as a central connect it with my...
Hello,
I have to develop a new device that has to connect as a central device to three sensors, and has to connect as a peripheral to a smartphone. The type of connection...
Hi,
I'm observing a strange behavior with the UARTE peripherals on our nrf52840 based board when I'm trying to use a specific pin as TX.
In particular, I'm actually using...
Hello,
I've flashed to my custom nRF52832 board the ble_app_hrs_pca10040_s132 example, it works fine with iOS and Android hosts but when I try to connect to my development...
Hi Team
I have read https://devzone.nordicsemi.com/f/nordic-q-a/75801/request-tolerance-in-the-d-e-dimension-of-nrf52833-wlcsp . and https://devzone.nordicsemi.com/f/nordic...
The board is nRF5340 DK.
nRF Connect SDK1.8.0 / Windows
Example Peripheral UART.
I want to DECLARE them, not change them with different types of functions. There are...
We have given 1.8V supply voltage for nRF52840-QIAA in our application.
The following data is given in datasheet:
1) VDD,POR VDD supply voltage needed during power-on...
Hello,
I am having some build issues when attempting to add support for a Skyworks FEM to our application built with NCS 1.7.0 for a NRF52820 target. Our board file is...
HI All,
We are using NRF52832 for our project.
1) Can we wake up the NRF52832 chip from sleep mode using Bluetooth Event?
2) Can we wake up the NRF52832 chip from...
software: ncs v1.8.0
hardware: my test nrf52833 board, with 9 antennas.
I do experiment like this:
aoa rx: in "nrf52833dk_nrf52833.overlay" file, I set " dfe-antenna...
Good day all.
Im finding my self working in a circle and not quite sure how to go about this. My USBD_HID device code with my Neopixel lib work well together. I now need...
