Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Dear, We are working on a project where we have to request and read out data from multiple (up to 50, but can split up to 8 per central device) BLE modules (BK3432_QFN32)...
Hi!
I am totally new with Segger, so this is an idiot's question:
When I open a sample project and want to check my settings using the
"Configure nRF connect SDK Project...
I can't seem to be able to activate the iBasis sim card.
I'm in Norway.
It gets passed the initial screen and says the it needs user data. It then pre-populates with the...
SDK Environment: nRF Connect SDK v1.8.0 Target: Decawave DWM1001-DEV. This uses the nRF52832
My application uses more than half the flash size of the nRF52832.
Using mcuboot...
Hi, I'm working on nRF9160 modem firmware update.
For Understanding SPM with secure and non-secure firmaware, I have used UARTE2(secure peripheral) into non-secure firmware...
Hi All,
I am trying to run two UARTS using LIBUARTE.
this is the relevant configuration:
#define NRF_LIBUARTE_ASYNC_WITH_APP_TIMER 1 #define NRF_LIBUARTE_DRV_UARTE0...
Hi Everyone,
sdk : nrf Connect v1.7.0
ide : VS code
I was trying out central_hr sample on nrf52840 dk. I have simulated hrs server in nrf Connect mobile application...
I notice that the fork sdk-zephyr https://github.com/nrfconnect/sdk-zephyr
is missing important errata updates for nRF82510
as it is using and outdated https://github...
Hi, I'm trying to use the pwm driver to turn off or on a dc motor (which the speed will variate via the pwm signal). I need to achieve a frequency between 20kHz and 100kHz...
Hello,
How can I configure for a GATT characteristic which type will be used.
Without defining it will be a byte array.
I'd like to configure for example an int16 number...
Hi,
I am using Win10, nRF Connect 3.9.0, programmer 2.0.0. and I get "no matching trait found" when trying to program the 9160 on my board. I have seen a few other questions...
I am making a central application which connects to a peripheral and uses Peer Manager. The first time I connect, I have to call pm_conn_secure() to secure the link, basically...
Problem connecting nrf51822 and ESP32 BLE with LESC while using static passkey.The ESP shows the following error logs:
W (1280) BT_SMP: Non bonding: No keys will be exchanged...
Hi,
What is the role of the NRF_ESB_CREATE_PAYLOAD()
static nrf_esb_payload_t tx_payload = NRF_ESB_CREATE_PAYLOAD(1,0,0,0,0,0,0,0,0,0,0);
how it works
if i create...
