I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi! I'm a beginner working with a project that uses nRF5280 Softdevice 6.1.1 and have some questions wrt to the peer manager and its ranking system . I can see the whitelist...
to who it may concened
nRF5_SDK_15.2.0_9412b96
i used tool to write the s140_nrf52_6.1.0_softdevice.hex and nrf52840_xxaa.hex(from example ) to NRF52832 by nrf connect...
Hi,
I have a C++ array or structure initialization issue that only occurs on nRF9160, but not other devices.
I am looking at the possibility of using JEDI in our IoT devices...
Hello,
I'm working on a project involving both the nRF9160 and the nRF52833 on a single PCB. Since PCB space is at a premium for this project, I would like to know if it...
Regarding the new modem command AT%RAI, the documentation here says:
In addition to using the %RAI command, the application must tell when the data connection is not needed...
I have logged in, I am using the same email address and I have read and - I believe - qualify for the license agreement.
Can you please look at why my request is denied...
Hi,
I am trying to migrate my project from 52832 to 52810, somehow i found the services can't be discovered. And seems that on phone it's looks like it is connected, but...
Hello,
how to activate the Early Release Assistance Indication, to bypass the RRC_CONNECTED state.
This page from Telekom suggests that the user can do that to save much...
I saw in some post smart Bluetooth can have 7 active device. I would like to know what is the maximum number of Bluetooth devices i can pair up in sleep mode? i am doing a...
Hi,
I'm using SDK v17.0.2 on my nRF52840-based board. I have implemented buttonless secure OTA reflash and it generally works. When I get the NRF_PWR_MGMT_EVT_PREPARE_DFU...
We have some dev code where the workflow is as follows:
1. an engineering version of firmware is loadded to target. The target is erased then programmed in the normal way...
Hello,
I am using nRF9160 dk for prepare a program to I2C scanning for address. Can any one give a guide for start this task. Moreover, I am using Zephyr kernel on nRF9160dk...
Hello,
I want to read external accelerometer on nrf9160dk using I2C. But when I connect SDA and SCL pins of sensor to nrf91, there is no output.
The Code is:
When...
I am trying to set the UUID definitions for the Windows Application Bluetooth Low Energy 3.0.0. The only doc availible is for v2.3.1.
I tried to follow the following steps...
