I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I am using PPK 1 kit with nRF52 DK. The system is used to measure the power on nRF52840 DK using DUT mode. The system was working just fine until I started receiving...
Hi
I'm trying to use the nrfx TWI Slave function with IRQ (No Poll), but there is no clean code available I found.
I'm using the following code:
But even if I can...
Hello,
I am using NRF9160 running the Serial LTE Modem application in NCS 1.5.0. When connecting with AWS IoT over a secure MQTT connection the maximum MQTT packet size...
I'm using nRF5340 to provide Bluetooth connection to other devices. Almost all Android devices connect correctly, for example: Samsung S21, LG G8X, Xiaomi Mi Mix 2. However...
Greetings,
I am using nRF52832 QFAA E0 in my development stages and found no issues regarding the architecture I have been using. Architecture:
DFU is built separately...
Hi, I am fairly new to the NRF and was wondering if there was a way to increase the sampling rate to 100Hz. I have used the ble_app_uart example to configure this code:
...
Hi,
I am using nrf52832 DK.
SDK17.0.2 and Softdevice S132
I have a ESP32 C3 module as a central device which scans for BLE5 devices.
I have kept the nrf52832 DK...
Hi there,
I was wondering, is there any project or plan to use the nRF9160 as a modem with standard ethernet interface ? The ethernet interface could be either
- RMII...
Hello, I currently have nrf9160 devices deployed running nrf connect sdk v1.3.0 that fails to reboot into the secondary image. It specifically happens when I try to send a...
Hello. I orignally had an expired SIM card that came with my device, so I got a new SIM card to setup with the Thingy:91. These come with an EID of 19 digits, but no ICCID...
The fault was caught by the weak handler, which I think means it was totally not expected.
The trace starts from peer_manager_init() which is part of the Buttonless DFU...
Hi Nordic Team,
I was doing OTA in nrf52840 using Secure DFU ble example in nrf5 sdk. Where i want add some customizations in the code.
1.I wanted to add spis example...
The sample in nrf/samples/event_manager crashes when running on QEMU_x86 with the following output:
I'm using NRF SDK v1.6. Do I need to configure something in KConfig...
Hi Nordic Team,
Can I upgrade the firmware between different softdevice? From s132 to s113
firmware 1: sd: s132_nrf52_7.0.1_softdevice.hex , bootloader: secure bootloader...
