Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi, I want to build a Bluetooth LE peripheral application with nRF5340. The channel must be able to sustain an output stream of 8 kbit/s.
Other desirable features are: ...
GPS sample stops updating timestamp after a few days of uptime indoors
Tested devices: Thingy:91, nRF9160dk Tested firmwares: mfw_nrf9160_1.2.1, mfw_nrf9160_1.2.2
Demo...
I have a nRF52820-DK evaluation board which I am trying to develop on. I followed the manual install procedure on to my xubuntu Linux desktop. I followed these instructions...
Hi ! I have configured Zero bit length of S1 in radio packet ( nrf52840 ) but it is still mapped to the RAM.
... ((NRF_S1LEN_BITS << RADIO_PCNF0_S1LEN_Pos) & (RADIO_PCNF0_S1LEN_Msk...
We would like to use Zigbeee on the nRF52820, however, it seems from other threads that neither the "nRF5 SDK for Thread and Zigbee" nor the "nRF Connect SDK" support it,...
Hello sir,
I am using nrf52832 soc with customized board having gpio pin with P0.2,P0.3 and P0.4 used for led blinking for different purposes.The function used for led blinking...
Hello,
I have a problem with the SPI of the nRF52DK 52832, and Zephyr 1.6.1. I have to transmit 10 frames of 5760 bytes each to the TFT display with the ST7789 driver. ...
I am just creating this issue as a bug report. (my github issue: https://github.com/zephyrproject-rtos/zephyr/issues/38688 )
There is currently a bug in zephyrs handling...
Hi!
I had some time with the Thingy:91 and was able to get my own application running on the device using the nRF Connect Programmer application. To eliminate the need for...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I want to read / write a value to the specified address of the flash. According to...
Hello.
I'm trying to get data from a pressure sensor.
But it seems that BLE device is not properly got data from the sensor.
Here is a data sheet of the sensor. (Please...
Hello everyone, I am using NrfConnect with Zephyr on Segger embedded studio . I want tu use the math logarithm function in my code and print the result on the debug terminal...
Hello,
We have a wearable-type device with custom BLE services and characteristics. We would like to log all data from our services on a PC. Would you happen to know of...
Hello!
Can anyone explain, why APP_USBD_CDC_REQ_SET_CONTROL_LINE_STATE event in app_usb_cdc_acm library fires for DTR signal changes only, but not for RTS signal? I try...
