I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
(see image below for clarity of this text)
In our product, we have this requirement. - be able to update the application on the nRF9160. - be able to update the firmware...
I'm not sure what happened to my SES but every time I try to debug I get a message saying that my image is out of date even just after having rebuilt it. Any idea what may...
Hello,
I’m able flash my code to the nRf52832 with no problem. At this point all is well. The problem occurs when I power down the device and then power up. On power up...
Hi,
I was merging the files of peripheral hr in ble mesh chat project
how to add new .a project in nrf connect sdk using segger embedded studio and also how to include...
Have a catch-22 here.
Here is my code:
When I call nrf_sdh_enable_request() it returns the error '0x08 which is SoftDevice already enabled according to the documentation...
Hi everyone,
I use to use the nrf52840 dev. board with the SDK16 examples. Now I am facing a problem with all the BLE peripheral examples
1. When I build and run in release...
Hi there,
for a customer of mine I have to programm a Arduino 33 BLE but not using Arduino IDE but use the Nordic SDK.
As it is a normal nRF52840 (inside an Nina-B306...
I am currently working on a project in which I will need to increment the pwm up to full cycle in 'x' number of steps and then be able to step down 'y' number of steps when...
I'm using app_scheduler to pass UART events in the "main thread". I'm storing multiple data types in a struct (arrays, integers) and I've set the max event size to the size...
Hello Team,
I am using the OT-nRF52840 source and working on the end device. I want to add the I2C(TWI) support in my end application, but as soon as I add any API it shows...
My problem is similar to this
https://devzone.nordicsemi.com/f/nordic-q-a/64696/projects-for-writing-into-flash-memory-does-not-work-on-nrf52840-dongle/264746#264746
except...
Can a "Pin Reset" recover the nRF52810 part if the part has encountered a slow voltage rise, greater than 60 ms, from 0 - 1.7V (described in the image below)?
Hi, I am new to nordic and zephyr and I have a sensor (Melexis - MLX90641) and I would like to test it on a custom board using nRF9160.. I add the sensor into the dts files...
When I open the nrf connect sdk project, it goes like this,
How can I fix it?
Creating solution direction_finding_connectionless_rx.emProject cmake -GNinja -DBOARD=nrf52833dk_nrf52833...
