I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I'm trying to flash an external board using the Ezurio BL54L15 module, with the nRF54L15-DK as the debugger. SWD is connected via the DK's Debug Out header to the module's...
Note: related to
Last week we had an issue regarding camera flash triggering reset and undefined behavior in our nRF52832. We have been able to reproduce this issue in...
Hi Everyone, I'm using nrf9160 sip, mfw_nrf9160_1.3.7 modem firmware version, slm example, sdk v2.8.0. When I include lte_auto_connect() function or manually configure the...
Hi Support Team
We want to use Windows PC to do the BLE FOTA for nRF52840 BLE device. The following DevAcademy exercise mentions that AuTerm can be used to do the FOTA on...
Hi
I found another bug in the BMA4XX driver.
When using "CONFIG_BMA4XX_TEMPERATURE=y" there is a compilation failure.
Line 621 of bma4xx.c:
Unfortunately the...
I am using Segger Embedded Studio V8.24 with nRF5 SDK 17.1.0 to build the example ble_app_bms_pca10056_s140 . This is the original Nordic example without any changes .
When...
Hi!
I have just received the nRF52840DK board and am currently perusing its schematics. Please don't be annoyed by my following question, but there are things I'm quite...
Hi,
I have tried the led strip example program and it works. My project will use 88 WS2812B RGB LEDs. For testing I used only 5 WS812B RGB LEDs. If I want to turn on red...
I have some questions regarding the power consumption for the nRF54L.
For sleep current:
1) The summary table shows 96kB RAM retention w/ GRTC is 2.0uA, but later in the...
Hello,
I've recently picked up Thingy 53 and NRF7002EB shield and wanted to play around with it, but I have a problem during project configuration.
When I add -DSHIELD...
Hi, I just tried installing nrfutil on linux with aarch64 architecture and with i try to use it i get error.
how i installed it:
after installation I ran the...
Hi, With nRF5340 DK, I am using CC registers of NRF_TIMER2 (as a free-running Timer), and DPPI, interacting with Radio. I set up a Timer Compare (functioning as a timeout...
Hi, I am having trouble setting up the partition manager in external flash with nRF54L15dk in NCS 3.0.0. I did not find any examples of this working. Interesting thing is...
1、How can I find the QEDC configuration for NRF54L15 or the QEDC demo? I found that Nordic courses do not offer these options. 2、Another issue is that I am using QSPI routines...
Hello,
If I set the connection interval to 300ms, can I call bt_nus_send multiple times (e.g., every 100ms) within that interval?
Additionally:
How can I check if...
