I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I need help to disable shell_uart and its commands used in UART of BLE mesh chat example as i want to configure this UART for custom protocol along with RTS signal to...
Hi Nordic:
I am currently working on Bluetooth Matter product certification and require the certification materials for the nRF54L15. While filling out the application form...
I am using a custom board with a nrf5340 chip on it with vs code and sdk/toolchain of 2.9.1 and the bmi270 sample. I am getting and issue with my bmi270 accelerometer when...
Hi,
The nRF9151 DK product page indicates that the DK includes among other documents the hardware schematics and layout files. I've purchased the DK kit, but as far as I...
I am trying to build an application on nRF Connect SDK on VS Code and I keep getting this error:
c:/ncs/toolchains/0b393f9e1b/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc...
Hi All,
I am experiencing a significant voltage drop issue with the NRF-PPK2 device after a recent firmware update. When I set the source meter output to 3000mV (3.0V) at...
Hi All,
PPK2 isn't accurately measuring currents below 20 μ A, showing 0 nA instead. This started happening after you updated your nRF Connect software, and reverting...
I am using the nRF52840, nRF5_SDK_3.2.0, using example: usbd_cdc_acm. I mofified the example so that I transmit characters from a serial port to the USB using a virtual COM...
I have tried init modbus RTU on my nRF9160 with SDK2.5.2 using max485 module but i have faced an error. This is the error: *** Booting nRF Connect SDK v2.5.2 *** [00:00:00...
Hi forum ,
pls help me for flash erase ,write and read to be successful for windbond w25q64 here i m stacked a long days if possible pls send me a sample successfull code...
Hi,
I noticed that NCS has been updated to version 3.0.2. I now want to compile the beacon in host-only mode and make it work on the nRF52832, but I haven't succeeded so...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi,
I'm trying to set up SEGGER SystemView on our custom nRF5340 board for debugging purposes using the SEGGER SystemView application.
Below is the configuration I'm using...
Hello,
Our project using NRF5 SDK V17.0.2 require SBOM (Software Bill of Materials). Do you know if there is one readily available? If not, do you know how to obtain/generate...
Hi, I am new to blue tooth mesh, but want to develop a test system with blue tooth mesh. Eventually I would like to be able to create a blue tooth mesh network to provision...
