Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello, I make multii-link peripheral device with 3 BLE HID connections. I extend heap and stack to 16kb and set properties RAM_START=0x20004000 RAM_SIZE=0x3c000. As the base...
Hello there! I wanted to plot data from ADC via UART using SerialPlot software. Unfortunately it crashes, despite I choosed the proper COM port, baudrate. No matter which...
Hi, I was wondering is there anything similar to DTM but suited for ZigBee certification? I read, that nrf_802154 driver could serve as a starting point for this implementation...
Myself Satej from FLEX,we are collecting soldering and washing data for our manufacturing site in SENAI.Please help to provide below mentioned data.
MPN
Manufacturer...
Hello, All
I am developing on windows and want to use shell tools. And saw some descriptions about the shell on the official zephyr document.
But I don’t know how to use...
HI
How put mcuboot whit FOTA, primary slot in cpu flash and secondary slot in external flash?
I need more memory for my application.
thanks for your support.
Faus...
Hello,
In my board, nRF52832 is connected to other MCU.
And those two communicates via SPI. nRF52832 is master.
To synchronize two boards, MOSI pin has to be used...
Hello,
Central uses nRF52840, and multiple peripherals use nRF52832.
The central is paired with each peripheral device , and each communicate.
To do this, I am developing...
I am testing smp_srv (bluetooth) with NCS 1.3.2. I don't know how to build and flash related apps for MCU boot in NCS. MCUboot is unable to boot smp_srv even after running...
Based on nRF52 hardware，I want to develop a phone based on HID protocol to control the phone, send instructions to let the phone into the lock screen state，
How to go about...
Hi, DevZone, thanks for help : )
I'm try to porting DK Board's Ble Bonding function to Target Board.
TARGET : nRF52840
SD: s140_nRF52_v7.0.1
SDK: nRF5_v16.0.0
...
To whom it concerns:
I'm a little new to Bluetooth SIGs launch studio and need a little guidance on the correct QDID to utilize for my product using Nordic SDKs.
I have...
Hello,
I'm working on a program that receives the temperature over TWI, saves the temperature in a string to flash memory, then adds this string to an NDEF message to be...
Hello,
I have 4Pcs same PCBAs and same firmware, the current values as below:
2.2uA
3.3uA
3.0uA
3.8uA
Condition: Power Supply 3V Battery; Temperature 22...
Shalom!
We have a nRF9160 custom board on which I cannot switch some of the IO lines.
For example we have two leds, P0.9 an P.10 but only P0.9 works. The hardware guy...
