Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi Nordic DevTeam,
I am having this minor issue where the transmitting UART of the NRF (from phone to external MCU) is not responding as robust as I expected.
...
The fds_record_update was called successfully, and a successful callback was received.
When I use the nrfjprog -readcode command in SDK 13.0, I find that the data is missing...
Hi,
SDK: nRf connect SDK
Kit:nRF5340
I would like to configure a radio peripheral in application core. But radio peripheral is a feature of network core.
1. Can you...
I have implemented time synchronisation that is based on this example: https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/wireless-timer...
Hello,
I am using Nordic nRF52840 (nRF5SDK v16.0.0) and softdevice : s140.
Nordic MCU is connected to Host MCU over UART interface (baudrate = 115200). I have below observation...
hello,
i am using nrf52840 with sx1276 i am trying to change some of the calls from arduino to nrf52840 can you tell me i am doing everything right
#define DIO0 NRF_GPIO_PIN_MAP...
Hi. I use NCS SDK 1.5.1 with NRF5340 .
I took the project from: \zephyr\samples\portability\cmsis_rtos_v2\philosophers\ as base and try to add two additional tasks.
Application...
Hi,
I would like to implement cell triangulation with the nRF91 in order determine the location of the device via cellular. I already had a look at the available posts such...
Hi friends:
My ble mesh gateway want to remove a mesh node
(a): Which api can i use to realize this purpose?(My SDK is nrf5_SDK_for_Mesh_v5.0.0)
(b): There is a special...
Hi Community! We're happy users of a range of Nordic solutions on behalf of our clients in Europe. Now we're facing a new challenge: one BLE device that should act as a sort...
hello,
i am using nrf52840 with sx1276 module i am using an library which consists of c and c++ files i want to complie both the file but when i complied the following c...
Hello!
I think I have the below problem, except I am using NRF52840 and therefore PCA10056. I am using SDK14.2 and the alpha softdevice. I am aware these are out of date...
Hello everyone, I would like to ask about the examples of openAMP in nrf5340. I only saw examples of network core in nrf\samples\nrf5340\multiprotocol_rpmsg. Where should...
