I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Currently, I am using the ble_app_cts_c example and I want to disconnect the connected device.
I want to know how can I check the condition for any connected device?
and...
Hi.
i am using NRF52832 DK with MESH SDK
can i transmit string from Low Power Node to Friendship node.?
If yes kindly let me know what changes i need to do for that...
I have observed two issues with using the UART in an ncs project and I'm not sure exactly where the issue lies (Nordic or Zephyr).
Firstly, and most importantly, according...
hello Nordic
i am using nrf52840, sdk 16.0 working on ther peripheral ble_blinky example, working with Segger IDE (ses)
i have lines of code missing when i am debugging...
HI,
I am trying to connect multilink central to multiple peripherals. I am able to connect using "target name". But i dont know how to connect using central to peripheral...
HI,
Currently, I am using the ble_app_cts_c example and I am able to pair only one device. I found out that it is related to whitelisting function.
How can I disable the...
On SDK16.0.0 + Mesh SDK 4.1.0
I've followed this to add PA/LNA support in the bootloader (Fanstel BT840X). I see the increase in RSSI and know that it is working.
...
Hi,
I am evaluating the Light Ctrl example of the Connect SDK 1.4.2. After nRF52840DK was programmed and provisioned by iPad, Mesh App, I was trying to bind application...
Hi,
I have built the example hrs_uart project and it works fine when I load the image into a pair of OCA10040 demo boards, one as application board and the other as connectivity...
Hi,
I am currently testing QSPI communication for flash. I am using the Termite console. When the console starting I got this error message:
uart:~$ [1B][8D[1B][J[00:00...
Hi,
I am trying to create a Mesh Network using CCT controlled lights and switch.
I want to fetch the present lightness value of the light(server) from the switch(client...
Hello,
I'm currently using SES for SW-development (NRF52). But especially for legacy code and refactoring I think this tool is absolutly not suitable (basic functions like...
Hi
We are using this combination of software:
Mesh SDK 4.2
Bluetooth SDK 17.0.1
Softdevice 7.0.1
Mesh DFU using the precompiled bootloader binary mesh_bootloader_gccarmemb_nrf52840_xxAA...
Dear sir,
Our code gets compiled using command emBuild.exe For programming NRF Connect Programmer tool is used.
I get following error while hex file is added to programmer...
HI All !
Hope you all are doing well !
I have a question regarding "Exporting Segger Embedded IDE Project/SDK to Arduino IDE or Vscode Studio" The Reason i want this is...
