I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I need to power my external board while debugging with the DK52. Therefore I don't use the VDD connection from the DK52, I only connect the external VDD to SH_VTG. ...
Hi Everyone,
I changed my old app_uart library for the new libuarte, which works really well whithout a SoftDevice.
Now I am struggling to make it work in my final...
I'm having trouble with the SAADC in scan and double buffer mode with 4 channels enabled, where 3 channels are external inputs and the 4th is the internal VDD.
It appears...
Hi there,
I am using nrf52840, Softdevice S140,on our custom board. And my Android app is based on nrf android library( Andoid-BLE-Library )
Application is based on SDK17...
Hello All,
I am using nRF52840 Dev-kit and nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 SDK. So far in development, I have used the GPIO edge triggering method to detect...
hi support team,
i just tested http_application_update project, and i set up one server on cloud:"106.12.30.214:32500",
also you can reach this file server from web...
Dear Team,
We are developing an Vibration Sensing System, it contains nodes and gateway where all the nodes and gateway are present in the secured mesh network.
And...
Hi,
I'm using two boards with nrf52832 and sdk 15.3.0. One alter the ble_app_mult_uart__c example as ble center ，the othe alter the ble_app_uart example as ble peripheral...
Hi,
I'm testing heart rate measurement example with my nRF52 DK. In the nRF connect application, I see the logs are converted from Hexadecimal value to user-readable values...
Hi,
I was following the example posted on the below link.
https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts/nrf-connect-sdk-tutorial...
Is it expected that the MQTT API does not receive any events unless a message is published to the server? I'm noticing that without a ping event or any message transmitted...
If I have a version 1.00 of my application which stores data in using flash data services . I make modification and version 2.00 of my application is a page larger.
1A)...
Maybe this is just a little nuisance but is there a difference pynrfjprog and nrfjprog ? There is no documentation on nfrjprog !
Searching infocenter for nrfjprog reports...
