Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I am using SES and nRF5 SDK v17.0.2.
I am tying to add a few peripherals (SAADC, I2C, SPI, etc.) to the peripheral UART example with EVK (ble_app_uart_pca10040_s112)....
Hi,
I am using 'power profiler kit 1' with the latest desktop (windows) app (nrf connect 3.6.1 and power profiler 3.0.3). The setup was working fine with the older versions...
Hi everyone,
Because of experiencing stability issues using the app_uart implementation for UART communication, I recently switched to the libuarte_async lib which works...
I'm trying to run two UARTs out of my NRF52840. Do you have an example in which both SoftDevice UARTs are used? The Nordic Infocenter SDK 14.0.0 documentation lists one of...
There seems to be a blanket statement of v5.1 compliance here:
https://www.nordicsemi.com/Software-and-tools/Software/S140/Download#infotabs
Does this apply to all revisions...
Hello, when will the v8.0.0 version of the SD for the nrf52840 be available? It seems to be listed in the SIG webpage, but not available for download on the nordic webpage...
Hi,
While trying to measure timings with input captures and pin interrupts, I noticed that the SDK-provided pin changed event is very slow : by the time my handler starts...
I am trying to port my working application from a nrf52811/s112 to nrf52832/s132, both with SDK 16.0.0. I'm at the end at the process, it builds fine on nrf52932, I just can...
I'm new to develop firmware on nRF9160-DK, and my first target to add APN to use LTE-M.
For now, I'd like to do a simple way in the below even this is temporary.
=> Hard...
Hello,
I try to transfer the thread_mqtt_sn_client_publisher example from the pca10056 to the pca10059.
Before that, I tried out the example with the pca10056, a boarder...
Hello! me and a coworker are developing a library for communicating with a peripheral via UART. The main idea is that when we send a command, we should get the corresponding...
Hello Team,
I am new to the OTA process for nRF52840. Please help me with the below query.
1) Is it possible to perform the OTA over BLE and over thread network as well...
Hi, We use the QSPI already very well for a flash device that has the correct commands. Now we want to use a SRAM, also QSPI prepared, but it has some other commands, there...
I'm trying to decide on a protocol to use between two nRF52840s.
Both will connect to an App and each other at the same time
Latency is important because the communication...
