Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I am integrating a sensor on SPI 1 with cellular but device get stuck in CPU idle when first transaction of SPI is made?
I am using nrf9160dk_nrf9160ns as board configuration...
Starting with the dev kit, where I get correct behavior. First, I make sure the RESETREAS register is all zeros. I do this like so: NRF_POWER->RESETREAS = 0xFFFFFFFF; while...
Hello,
I am using nrf9160 and want to test the just simple SPI function. The code that I found from github( https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples...
Is there a way to set duty cycle before app_pwm_enable(&PWM1) call ?
Or some other simple way to switch on and off a passive buzzer signal without every time at off/on cycle...
Hi:
We're working with a 3rd party testing agency for our product that is using SDK 11 with S132 Softdevice 2.0.0.
If I understand correctly, the SDK allows up to 6 transmit...
I am trying to implement a system / integration test of a BLE device.
I would like to use the nRF52840-Dongle in my PC and use the PC-BLE-Driver for Cpp as the Central....
As you could see from the below image, the SCL signal at 400kHz is NOT a good square wave.
1) Why & how to solve it, please?
2) Also, why SCL is between 0.4V to V_DD=3...
I am now pulling my hair out with these drivers ... I'm trying to do what I think is the right thing and use the new nrfx drivers, but it's really not easy.
So this started...
Hi, I am using Zephyr's BLE for transmission In the peripheral, I record the time when I send the notify to cental (start time) Then when I received the central write_without_response...
Hello,
I have a peripheral that is connected to nRF52832 using I2C, in which I want to send some file to its memory. However, for sending this file, I need to stream it...
I have an existing BLE project that works as a mesh but does not use nRF SDK for Mesh. Using sdk 17.0.2, s140 7.2.0 on nrf52840s and visualGDB.
It works well for most clients...
Hi, I want to evaluate my anttena design. I have tuned it. With the dongle I can scan the air for radio signals, I see then my Wifi and I see the BLE radio of my board. Now...
Hello Nordic Community,
In order to measure battery voltage, I am using ADC with the code implemented as below:
In this, there is a while loop used to wait for ADC to...
We are developing an IoT device communicating via LTE to AWS IoT Hub using authentication by client certificate. For that, we are powering on the modem, do a mqtt_connect...
I am on nrfConnect v3.6 trying to build an SPI test using the command line (west)
I get this error:
```
error: SPI_3_NRF_SPIM (defined at drivers/spi/Kconfig.nrfx:133...
