Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
We are using a custom ARM board which runs Linux and has a UART interface to a nRF9160.
I'm not how to phrase this exactly so I will just describe what I would like to do...
Hi,
I am using nrf51 DK and MDK is keil5
SDK : nRF5_SDK_12.3.0_d7731ad
softdevice : S130.
when i load the code nRF5_SDK_12.3.0_d7731ad\examples\peripheral\twi_sensor...
I have used light_Switch example from nrf mesh sdk nrf5_SDK_for_Mesh_v4.2.0_src I like to get the client source address in nrf_switch_server what should I need to modify to...
hello Nordic
i am using nrf 52840 dev kit, sdk 16.0
i want to make a sampling of 2 channels at 32MHz rate. the data shell be passed to RAM via easyDMA, after every 4...
Hi, I try to change my MAC address, but return error code 8.
check error code 8 is :
So I try set the mac address after ble connected. and the function sd_ble_gap_addr_set...
I'm trying to drive LEDs using PWM on Thingy:52 and Zephyr OS. It works when I connect external diodes to GPIOs, but built-in LEDs are connected to I/O expander instead. ...
Hello,
I have an Android application that sends and receive data from a nrf52832 peripheral.
During a test for our device using a nrf52932 chip, 2.4GHZ noise is emitted...
Hi. I bought the BM832E development board and have not yet ordered the DK board.
It says that arduino uno rev 3 is compatible with it. Does this mean I can plug my arduino...
Hello,
I am using nRF52 DK development board. I'm having a problem when I load simple blink example . I am getting an error message Error: Flash Download failed -...
Hi all!
Im still new to this and I'm trying to help a friend with a PCB design. We are using the nrf52832 and recreating the design from the reference circuit given in the...
I am trying to Compiling ‘ble_advertising.c’ and get 'NRF_EVT_FLASH_OPERATION_SUCCESS' undeclared (first use in this function).
This declaretion is already in the nrf_soc...
Hi;
i tried to compile LED Button app founded in this tutorial infocenter.nordicsemi.com/index.jsp in nrf51822 pca 20006 I had these errors someone can help me please or...
I just make some change Tx power level on "ble_app_blinky" app, i see that: when change Tx power(-20, -16,.., -4, 0, 4) like this code i mark red color below.
---------...
Hi,
I was trying to load the agps sample code into thingy 91 for testing. I read the readme document which mentioned that code is compatible with thingy 91 too.
After...
Hello everyone,
I wanted to start with Thingy:91 today, so I first wanted to update the device with the newest firmware.
First thing I found confusing is: On the Getting...
