Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi everyone,
I saw a lot of example in SDK (CDC ACM example, Audio example, MSC example,...) and I want to know if is possibile to modify them and use the USBW (USB WIRELESS...
nRF5_SDK_15.3.0_59ac345\examples\peripheral\twi_master_with_twis_slave.
I use NRF52810 as a slave, power consumption is 6uA.( nrf_drv_twis_enable(&m_twis);)
I see the...
Hi,
I am using nrf52832 module, sdk 17.0.2.
I have ble nus service added and device works properly had no issues till i add the AES related files and defines.
Can...
Hi,
I would like to use external app firmware to update over BLE a secondary microncontroler behind a NRF52832. I read that it's an experimental feature but it's very intersting...
Hello, im newbie here. I using multilink NUS from example and i want somehow get peripheral (peer) address in ble_nus_c_evt_handler TX event. How can i receive that?
I use nRF52832, sdk17.
First of all, during the sample, you want to implement central using "ble_app_out_c" in the "ble_central" file.
Central wants to connect peripheral...
Hi, I found that after migration from Zigbee Thread SDK to Zephyr GDB debugging functionality is broken. I have read a lot about PRIMASK register, GDB hooks, and so on, but...
Hi everyone,
I am using a third party nRF52840 module and I have developed my own bluetooth application. I have implemented one characteristic for notifying data from the...
Hello,
I am working with nRF52840 and started with SDK15 examples with BLE security mode 1 level 2, No MITM. I have a question regarding bond handling and the deletion of...
Hello everyone,
Using
PTS version is the latest (7.6.2),
nRF52832
SDK14.2.0
Softdevice s332 v5.0.0
When I run the test GAP/ADV/BV-01-C and so on, it constantly...
The settings.hex file is 6 K ,
the bootloader.hex file is 68 K ,
the softdevice.hex file is 429 K ,
the app.hex file is 183 K.
app.hex is just made for DFU function...
Hello every one.
I want to ask about:
Does NRF52810/NRF52811 support BLE_Central role with "S122" and "nRF5_SDK_17.0.2_d674dde"?
I try to convert example "\nRF5_SDK_17...
Thanks in advanced. I can create tx power level service, but it just reads current tx power level, I set add_char_params.char_props.write= 1; add_char_params.write_access...
Hi,
I am interfacing a temperature and humidity sensor (si7021) to Nordic nRF52 development kit board. The sensor works fine and I can read accurate temperature (23 degree...
Hello,
I used a breakout board of the MPU6050 ( playground.arduino.cc/.../mpu-6050.jpg)
and the nrf52832 development board. There is communication between the two and...
