I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi there,
I'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK for Mesh, FreeRTOS and C++. Everything except one single thing is working. I've just implemented FDS...
I have installed the sdk v 1.4.0 via the toolchain manager (nrf connect 3.6.0). I am using windows 10.
Here are my problems :
First I dont have the launch ide button after...
Hello Team,
We have already done the PoC for the Openthread network. I have created a border router using nRF52840 as an NCP and multiple nRF52840 end devices.
Now my...
If I have a firmware project working reliably on the nRF52810, is it possible to build a single firmware image that will run on both the nRF52805 and the nRF52810? I'm not...
Hi,
I was trying to program my board using SEGGER, but it doesn't seem to be working (log provided in the picture below)
/resized-image/__size/320x240/__key/communityserver...
I was w ondering if I could clarify the GCC version which is suggested for use with SDK 17.0.2.
In the release notes, it states:
However in components/toolchain/gcc...
hi，
I have a puzzle in the BootLoader project
I'm not particularly familiar with the mechanics of this BootLoader
I try to run bootloar in nrf5340dk_nrf5340_cpuapp,use...
Hi
i am trying to use adc in nrf 9160 kit. where i got error "Example requires secure_boot to have SAADC set to non-secure! If not; BusFault/UsageFault will be triggered...
Hello,
I have been trying to implement the Elliptic-curve Diffie–Hellman key exchange using tiny crypt.
As per the API, a random number generator function needs to be...
I am running into a very perplexing issue on my custom board involving use of fStorage and the soft device. When I attempt to write to flash memory using fStorage API (using...
Hi, Team
I read below uart current consumption data from nRF52832 Product Specification v1.4. But I can't find similar data in
nRF52840 Product Specification v1.1. I want...
I use zephyr to do a spi communication on nrf52840, and my nrf52840 is spi slvae
I refer to the example of zephyr spi\zephyr\tests\drivers\spi\spi_loopback\src\spi.c At...
Hello,
I have developed 10pcs of one prototype with the nrf9160 SiP.
I have some questions regarding some errors im having.
Regarding the SIM 1V8 driver VCC, for...
