Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi, we are considering using Gazell on the nRF52840 with nRF5 SDK v16. What would be the maximum packet length and the maximum data throughput that we could expect? What would...
Howdy,
I am using NRF5 SDK v15.0.0 on an nRF52810 custom PCB and am having a problem where the specified event handler is not being called upon completion of an SPIM transfer...
After unpacking I followed the first step at nordicsemi.com/thingy91, which is to update the firmware. I followed the linked instructions to update the modem and application...
Hi,
I have few questiones to initiate developing our project taking BLE Examples and BLE Services as reference.
Now,First thing we have to do in examples is turn bluetooth...
nRF Connect v3.2.0 - LTE Link Monitor is running on Ubuntu 16.04, and nrf9160 fw is v1.0.1. When connecting the board to my laptop, all Modem, UICC, LTE, PDN are Green. But...
hello
i am working with nrf52832
my code is based on the Ble blinky example from centeral. i added to the code with ble, uart, saadc and pwm and it was working great ...
Hi,
Using nRFConnect for desktop I've noticed that when writing an attribute I usually enter the hex values of a byte array (e.g. "12" = 0x12) but on other occasions the...
Hi Nordic Team,
- Can I UART/SPI/I2C on any pin of NRF52832 which is mentioned general-purpose I/O pin ?
- Can NRF52832 wakeup via any general-purpose pin?
- Is there...
Hello My ap plic ation is based on your bootloader (secure_bootloader_uart_mbr_pca10056) and your example "ble_thread_dyn_mtd_coap_cli".
When I send a special command...
Hello everyone!
I just got a Thingy: 91 and followed the startup guide, updated the firmware, and installed the modem...
I had trouble using iBasis eSIM because there...
My question is how to handle large amounts of data over the Gatt service
Our Current setup is 10 devices all on a Mesh Network. We use nRF5 SDK for Mesh and NRF mesh BLE...
Hello,
My project requires me to send acceleration data to phone. So, i have started with Custom BLE app.
Since i need to send 3 values, of x, y and z-axis. So i need...
hello
i am using nrf52832, with ble (s132 softdevice), pwm drv, saadc drcm uart, and using app_timers
i have added the twi drv to work with an expander for start.
...
We are using the Android-BLE-library version 2.1.1 above Android 9 (API level 28, using Java 8) in order to connect to a BLE-MCU. This MCU advertises a custom BLE profile...
