I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi,
I'm using an ISP2053 (nrf5340) chip on a custom board and debugging using the nrf5340dk. I'd like to use P0.02, P0.03 as part of an SPI bus.
I set up a simple experiment...
With the transition of the RTC peripheral on the nRF52, nRF53, etc series to the GRTC peripheral on the nRF54L, it appears there is no longer any low-power counter that can...
Hi
I am currently working with my project with 52840 and i am using sdk v3.0.1 & toolchain v3.0.0 to develope.
I am learning how to use DFU over UART from the application...
I am having an issue with the nrfx_qdec driver in zephyr, I am trying to simply detect when the turn happens and the direction of the turn is. Most of the time this is triggered...
Hi,
I want to configure P2.06 of my custom board nrf54l15 as DI. I have added following configuration in .overlay file
And configured the pin as input as follows
...
Good day, I was attempting to test the radio performance of the NRF54L15. I ported over the Radio_Test sample project to try and transmit an unmodulated carrier wave at a...
When attempting to register my nrf9160-dk device on nRF Cloud, I receive a message indicating the device is already registered. I do not know which account registered it....
Hi,
I am currently trying to build the channel_sounding_ras_initiator sample without any changes. I was successfully able to build the channel_sounding_ras_reflector.
...
Hello,
I am implementing the Physical Activity Monitor Service which looks like this:
Every notify or indicate characteristic needs a CCC according to The...
I would like to know the recommended battery part that is suggested by nordic to work with the nrf5340 Audio DK. I saw some blogposts where it was mentioned that a 3.7V 1500mah...
Hi,
When using HSPI pins on the nrf5340, it has a dedicated chip select pin HSPI_CSN. Does this mean that only one slave can be connected to the high-speed SPI?
Or, can...
In our Zephyr-based nRF project we store configuration in NVS . For the production line we’d like every unit to leave the factory with default objects already written to flash...
Hello,
I've developed an application on the nRF54L15DK, and have bought Insight SIP's ISP2454, featuring the same chip. I tried flashing the new chip with a hello world...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
