Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
On SDK 16.x.0 only
Please Do not judge the quality of SDK based on number of entries here. This thread should be considered as part of Nordic effort to find issues and possibly...
Hi,
I am trying to interface MCP7940 RTC with nRF52840 DK. Initially, I am using a twi_scanner example from the SDK v16.0. Using the same example it is expected that I should...
Hi, I am working nrf52832. I want to send the string.
#define APP_ADV_DATA_LENGTH 0x1F /**< Length of manufacturer specific data in the advertisement
uint16_t length;...
I spent some time trying to combine example project ble_app_hrs_freertos and ble_app_uart so that I have a project with FreeRTOS that uses NUS bidirectional - without success...
I have received a dev kit and am trying to connect with it over JLink. I have connected it to my computer via the J2 micro-USB port. SW6 is set to default and Power Source...
nRF52840-DK (PCA10056) when connected to laptop, LED 5 blinks very fast and LED1 also blinks(slower than LED5) and board is not detected by the laptop. could any one please...
Hi,
We have encountered an issue where we are transferring data using our custom service back and forth from the nrf52811 to a remote test device and the radio becomes unresponsive...
I am attempting to write a basic I2C program using Zephyr, but I am currently unable to sent a single byte over I2C. Am I doing something wrong? I'd prefer not to use the...
Hello!
I have a characteristic defined to be in user memory by the BLE_GATTS_VLOC_USER flag.
The initial length is 0 and the initial value pointer is NULL.
Now I...
Hello!
I am currently trying to use the watchdog driver from the Zephyr library. I have enabled the CONFIG_WATCHDOG and set it up similarly to the asset_tracker application...
Hi,
so far I have been programming my custom nrf52840 device through the debug out connector of the nRF52840 DK and a custom programming connector.
Now I would like to...
Hi,
I'm using nrf52832 to interface RTC using nrf_calendar.c file.
I have start the RTC at 8:59:00, it will reaches 9:00:00. After that automatically it will resets and...
I haven't been able to locate any NAND flash libraries or examples in SDK 15.3.0
To be clear, this is NAND flash, not NOR flash (examples are Toshiba TC58CYG2S0HRAIG and...
Hello!
We are trying to make a family of devices that would be based on nrf52840. The devices would communicate between each other via Bluetooth Long Range (CODED PHY)....
Hello,
I have a problem using the radio notifications. I use the softdevice V. 15.3.0.
I would like to have an interrupt every time I send an advertisement, which I can...
