Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
We are working on a project based on nrf51822. We have an application that needs to send 2 byte values to the mobile app every 200 milliseconds accurately(ideally 5...
Hello everyone,
I'm trying to communicate ble_app_uart and my customized mobile app(central) with static passkey my code as below
i facing problem when i make connection...
Hi,
Is it possible for me to manually flash the zephyr.bin on the nrf9160 located in proj/build/zephr/? I can flash the merge.hex however I do not want to use the merge...
I am investigating using a front-end module with a nRf52840 in an 802.15.4 application. I have seen the 802.15.4 stack in the nRF5_SDK_15.3.0_59ac345 SDK. It looks like there...
We have an application for using the 802.15.4 protocol with a nRf52840 and a Front End Module. We are looking for an approach to take for integrating the FEM control into...
Hi,
I'm trying to figure out if my device is suffering from errata 172.
* How can I know if I'm using Ble_LR125Kbit or Ble_LR500Kbit? * I'm trying to use the function...
To the kind attention of Nordic support team,
I would like to do a question that is not strictly related to Nordic, but I hope your expert can kindly give me an answer,...
Hello,
I am a student who tries to make a smart IoT project using nRF9160 DK and Arducam OV5642. I am searching on the internet to where to start, but I cannot find any...
If all you need is changing PHY, Tx power and Device Name in a standard nRF52840, do you need building a new bootloader from the scratch or the is a way to edit the standard...
Hello,
I'm experimenting with the nRF SDK for Mesh v3.2.0 and a nRF52832 DK, specific with the LPN example.
I want to enable BLE DFU support so I followed the instructions...
I am programming with SDK15.0. Then I use nRFgo studio to download the merged program to the DK board. But it reported a validation failure. So I tried to download softdevice...
I am building a project that is based on the custom service example https://github.com/bjornspockeli/custom_ble_service_example but I don't like how it advertises in a way...
Hi!
I am trying to test the Immediate Alert Client application example (ble_app_ias_c) from nRF5_SDK_15.0.0 on my nRF52832 based module. I want to understand how to test...
