I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I am using SES V4.18 with SDK 15.3.0.
In sdk_config.h, I have set APP_VERSION_MAJOR and APP_VERSION_MINOR etc...
Is it possible to add these numbers to the output file...
I recently added Mesh DFU support to a project that I'm working on but it's extremely slow. It will take at least 1 hour to update the network under ideal conditions but I...
Hi,
My stack is
s112
SDK 15.3
Segger
nrfConnect
nrf52832 DK
Power profiler kit connected via USB to my MAC to get the traces to run.
CR2032 batter removed...
Hello
I cannot load the Radio Test code onto the Nordic NRF52 devkit. I'm using SDK15.3 and the project located at C:\nRF5_SDK_15.3.0\examples\peripheral\radio_test.
The...
Hello,
I noticed this weird bug that coincides with the SD card not initializing using the FATfs.
Basically, I have the SCLK pin of the NRF52DK connected to a breadboard...
Hi All: I am using NRF51802 ,SDK is 12.30 version, and softdevice is s130 2.0.1 version. using keil MDK 5.23 Version. And download the softdevice using nrfgostudio and keil...
Hello,
I have a nordic nrf52840 on board, with another MCU (Cortex-M4) on board. Both chips are connected over UART.
I want to use the Cortex chip to perform firmware...
Hi.
We have a strange issue we are seeing with a nRF52840 where scanning fails, but it is very rare.
Setup - nRF52840 is a central device, and there are 20 x nRF52832...
Hello Nordic!
I'm developing with s340, nrf52840, and sdk 15.3.0
My device is a peripheral and the phone is master in ble.
I listen to my coworker who is developing...
Hi, I'm trying to set P0.20 pin as MISO of my spi master to communicate with ADXL372 accelerometer sensor, but when the miso is disconnected the signal received matches with...
Hello.
I want to develop a custom bootloader able to update firmware version Over-The-Air (BLE)
I'm using a custom Dev Board based on nRF52832 with and nRF SDK V15.0....
I am developing device that uses NRF52 and GSM modem. Sometimes when connecting to bonded device connection fails and phone pop-up appear and ask for pairing. GSM antenna...
Hello,
we are using nRF Connect for Desktop with a nRF52840 USB dongle for our testing purposes. I found no feature for “Request MTU” (ATT MTU exchange), like it is available...
Hello,
I am using nrf52832 board, having SDK 15.3.0, in Segger studio IDE, on windows10.
I am using bluebee board in which mdbt42q chip is used.I am trying to toggle gpio...
Hi
We have a lot of customers asking for full extended adverts features as per the latest spec in terms of all types of adverts and also other PHYs
Apparently other BLE...
