Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I am using nRF52840-MDK and connect to my Ubuntu running in VMWare. When I connect this device to my laptop and run pyocd-flashtool. I am getting a error message stating ...
Hi
I have purchased an nRF52832 DK to develop a human fall detection device. I'm a newbie to embedded studio, and nordic products. I just started to understand things on...
Hi, I have seen a few similar questions to this but the answers weren't too clear...I am trying to use both the long button push and the button push actions to generate separate...
Hello,
I have a Raytac MDBT50Q-RX USB dongle that I want to evaluate.
The dongle comes with Raytac's own test firmware.
In order to evaluate it for my purpose, I wanted...
I am very new begginer and dont know where to start about nordic nrf52832 chip. Started a week ago with downloading SDK and playing with examples in it.
I in specific need...
This is the structure.I am using bitfields here, even if i don't the problem still exists.
struct CODE_T
{ uint32_t guest_code_start_time; uint32_t guest_code_end_time;...
Hi,
Lior Neumann and Eli Biham found a vulnerabilitiy in BLE secure connections, to which CVE-2018-5383 was assigned.
Is the S132 SoftDevice affected by this vulnerabilitiy...
Hi Everyone
My requirements are as follows
1. I am running 4 tasks using free rtos in which one measures the ADC , 2nd sends the adc data over BLE and 3rd check if the...
hello
I am using sdk 15.3 example code of DFU (secure_boot loader \ pca10040_ble)
I want to debug code but i can not.I getting error like that "Error Flash Download Failed...
Hello,
I have been using this method for a while now and everything seemed to work. But for one of my device the method returns the error 0x3400. I wanted to know where...
I am trying to share ADC output to Bluetooth device. But issue is as I am getting SAADC output via SPI protocol.
Now i have added SAADC+SPI in BLE app uart example, So when...
I am trying to share ADC output to Bluetooth device. But issue is as I am getting SAADC output via SPI protocol.
Now i have added SAADC+SPI in BLE app uart example, So when...
Hi there,
I want to do scanning existing networks and for these goals, I need to enable Commissioner on Commissioner side. I use the otCommissionerStart function but when...
I am looking for an example that can work with Android 6 and higher
Current examples on Github have compilation problems probably using older gradle.
The application need...
Hi,
I'm wondering why SES 4.18 requires an entire rebuild of an application each time a project is (re)opened? I would have though it would perform an intelligent incremental...
