Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
In order to send an SMS in PDU mode, I need a Service Center Address. Normally, you can find it via AT+CSCA, but this does not seem to be supported on modem firmware v1.0...
I have a central device (nRF52832/Soft device s132) that connects to two peripherals. Both peripherals send data to the central via NUS. I have incorporated the required changes...
hi guys , I'm trying to use the ble mesh protocoll for my master thesis. I need to send a message always when an interrupt on a gpio pin occur.
there's a problem beetwen...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
chip: 52832 . sdk 12.3\examples\ble_central\ble_app_uart_c\pca10040\s132,
i use this example to scan ble advistisment, i want to write some date to flash, i use flash_word_write...
Hi
I am doing a mesh application with :
--SOC:52832;
--with an AT Command Module connected UART;
--Mesh SDK :3.2;
--SDK 15.3;
in order to manage call backs from...
I built ...\examples\dfu\bootloader_secure\secure_dfu.eww ,pass,then when download to PCA10040 board to debug,but it show error" ELF/DWARF Error: Unsupported .debug_info format...
I am running custom firmware on a custom board using an nRF52832 chip. I have encountered an issue after migrating my project from SDK 14.2 to SDK 15.3. The issue is that...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hello,
Since I migrated from SDK 13 to SDK 15.3 I can not see anymore print of NRF_LOG_DEBUG, NRF_LOG_INFO, NRF_LOG_ERROR and so on, on segger Jlink Viewer.
I have tried...
Are the following arguments correct?
data_rate <RADIO_MODE_MODE_Ble_1Mbit> or <RADIO_MODE_MODE_Ble_2Mbit> and so on.
output_power <RADIO_TXPOWER_TXPOWER_Pos4dBm> and...
Hello,
We are using the nRF52832 and 2G(GSM/GPRS) module to build up one IoT product. We got a disconnect between nRF52832 with other master instance(mobile phone APPs)...
Using Softdevice s140 v6.1.0 nRF5 SDK v15.2.0
I am trying to write to the flash, here are my read and write functions:
Two problems:
The write function does not...
Hi,
I've added an instance of the Generic Power OnOff Setup Server to an element and I can see it and all the models that it extends, i.e. (Power OnOff Server, DTT Server...
Hi all!
I'm trying to run the light_switch example (client and server), and i cant complete the provision process.
I'm using my phone and Nordic app for provision, when...
